FRP Grating for Australian Screening, Conveyor and Tailings Walkways

Project Case Studies
Direct Answer

For Australian iron ore sites in the Pilbara we specify pultruded and molded FRP grating on screening deck walkways, over-belt conveyor platforms and tailings pond access paths. The panels stand up to iron ore dust, abrasive spillage and outback UV, carry 12 kN/m2 at 900 mm, and clip down with SS316 fasteners so crews work without a hot-work permit on a remote site.

  • Best for: Screening walkway, over-belt platform, tailings path
  • Specify when: Isophthalic polyester, 50 mm pultruded, grit top
  • Key spec: 50 mm pultruded, 15-17 kg/m2, 12 kN/m2 at 900 mm, SS316

An iron ore operator in the Pilbara had been replacing steel grating on three routes every four years. Ore dust, abrasive spillage and outback UV at 50 C all attacked the zinc coating from above. We supplied 50 mm pultruded I-bar panels with grit tops, cut to the existing support spacing and fixed with SS316 clips. Three years on, none of the three areas has been blasted, recoated or re-clipped, and the mine has stopped flying in welders for grating repairs on remote shutdowns, which cuts shutdown cost.

Site conditions and the three project cases

Why steel fails on a Pilbara ore site

Painted steel grating on an Australian iron ore site rarely lasts beyond four to five years. Iron ore dust is abrasive and wears the top bar like sandpaper, while spillage from the screen piles up on the deck and traps moisture. Outback UV at 50 C embrittles the zinc within months, and washdown water after screen changes sits on the plate. By year four the bar ends thin, the welds crack and the mine books a shutdown to fly in a welder. The ore dust, spillage and UV combination is what kills steel on the screening floor.

Case 1: walkway around the screening deck

The screening deck walkway runs around the vibrating screens where operators change punch plates twice a week. Ore dust and abrasive spillage cover the deck, so painted steel wears thin at the walking line. We installed 50 mm pultruded I-bar panels with a grit top, spanning 900 mm between the existing steel supports and clipped with SS316 fasteners. The open mesh lets ore dust fall through instead of packing, and the grit stays non-slip even when the deck is covered in fine ore. Screen-change crews report less slipping than on the old steel, which used to be polished smooth by dust.

Case 2: platform above the transfer conveyor

The over-belt platform sits above the main transfer conveyor where maintenance crews walk to the belt scrapers and idlers. Ore dust blows across the deck all day, and steel here wore through at the clip holes in under four years. We supplied 50 mm pultruded I-bar panels with a concave surface, pre-cut around the transfer chute and the idler access. The panels weigh 15 to 17 kg/m2, about a quarter of steel at equal stiffness, so the existing structure carried them without modification. Crews now walk the belt during running hours because they no longer wait for a hot-work permit to repair a section.

Case 3: access path along the tailings pond

The tailings pond access path runs 80 meters along the perimeter berm where operators check the slurry lines and the decant valve. Salt-laden seepage and outback sun attack steel from below, and mild steel clip holes corrode within three years. We laid 38 mm molded isophthalic panels with a grit top, clipped to galvanized stringers with SS316 fasteners. The UV-stabilized resin keeps the deck from fading, and the grit stays non-slip when the path is damp from seepage. The path has gone through two wet seasons with no pitting at the support points at all.

Product selection, maintenance and specifications

Product types and resin selection

Isophthalic polyester was the right resin here because the media are ore dust, alkaline seepage and outback UV rather than strong acids or solvents. Isophthalic handles UV exposure and mild alkaline water well and stays cost-competitive. For the longer over-belt spans we moved to 50 mm pultruded I-bar, which weighs 15 to 17 kg/m2 and clears wider gaps than molded. Surfaces follow duty: grit top for the screening walkway and tailings path, concave for the over-belt platform. Every clip is SS316, never carbon steel, so the fasteners do not become the failure point on a remote site.

Maintenance and service life

Maintenance is limited to a quarterly hose-down to wash ore dust off the grit, and an annual walk-around to check clip torque and the sealed cut edges. The factory seals every edge so moisture and alkaline seepage cannot wick into the glass fibers. We expect 15 to 20 years of service on the screening floor and over-belt platform, against four to five years for painted steel. Spare panels are pre-cut to the same size, so a damaged section swaps in with hand tools during a scheduled shutdown. No grinding, no welding, no flying in a welder is needed to keep the walkway in service.

How to start your project

To quote an Australian mining project we need three inputs. First, a sketch with support spacing, screen elevation and the width of the walkway or platform. Second, the environment the deck will face, including ore type, seepage chemistry and summer temperature. Third, the loading case, whether operators with tools or light vehicle traffic. We come back with a load-table check against the m38 rating of 12 kN/m2 at 900 mm, a resin recommendation, and surface swatches for site testing. Our Nantong plant has exported to 45 plus countries for 20 plus years. Send the seepage chemistry and the support spacing first; the resin and thickness follow from those two.

Standard specifications and delivery

Standard molded panels ship at 1220 by 3660 mm and pultruded panels are cut to length at the factory, so the on-site crew only does light fitting around chutes and brackets. Thickness options cover 25, 30, 38, 50 and 65 mm, with the 65 mm panel at 38 kg/m2 for heavy zones. The minimum order is 10 m2, and lead time runs 12 to 36 working days depending on resin and thickness. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. Each shipment carries the ISO 9001 certificate numbered 01708Q11888R0S and the ASTM F3059 report numbered 211122012SHF-001, with SGS inspection on request. Panels are bundled by screening area and labeled by bay so the installer can stage them on the pad without a crane.

Key takeaways

Three points sum up this Pilbara mining job. First, the painted-steel replacement cycle of four years is gone; the pultruded panels are now in year three with zero recoating. Second, the 50 mm pultruded panels clear the longer over-belt spans at 12 kN/m2, which is the rating most screening walkways need. Third, SS316 clips and factory-sealed edges remove the two points that used to corrode first. If you are rebuilding a screening walkway or an over-belt platform, start with the seepage chemistry and the support spacing, and the rest follows.For the technical background see UV-stabilized FRP grating for Australian mining and coast and Heavy duty FRP load capacity for I-bar and molded.
Which resin handles Pilbara UV and ore dust?
Isophthalic polyester is the standard call here; it handles UV and alkaline seepage well, and we back the panels with the ASTM F3059 report numbered 211122012SHF-001.
Can a damaged panel be swapped on a remote site without a welder?
Yes. Panels clip on with SS316 fasteners and need no welding, so two fitters lift out a section during a scheduled shutdown with hand tools.
What lead time applies to a pultruded mining order?
Standard isophthalic 50 mm pultruded panels ship in 12 to 36 working days depending on length, with a minimum order of 10 m2 and ISO 9001 certificate 01708Q11888R0S attached.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026|Category: Project Case Studies|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating for Offshore & Marine
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Project background

The case covers an iron ore operation in the Pilbara region of Western Australia, where painted steel grating on three routes was being replaced on a four-year cycle. The three routes are the walkway around the vibrating screening deck, the service platform above the main transfer conveyor, and an access path along the tailings pond perimeter berm.

Ore dust and abrasive spillage cover the walking surface, outback summer temperatures reach about 50 degrees, and UV exposure embrittles the zinc coating within months. Washdown water after screen changes sits on the plate, and salt-laden seepage attacks the supports from below. The customer asked for a non-rusting, non-welding alternative that could be fitted during a remote shutdown without flying in a welder.

Specifications and load ratings

The screening walkway and the over-belt platform are supplied as 50 mm pultruded I-bar panels with a grit top on the deck route and a concave surface on the conveyor route. The panels span 900 mm between the existing steel supports and are rated for 12 kN per square metre at that span, which is the personnel-with-tools load class most screening walkways require. The pultruded I-bar weighs about 15 to 17 kg per square metre, roughly a quarter of steel at equal stiffness, so the existing structure carried the panels without modification.

The 80 m tailings path uses 38 mm moulded isophthalic panels with a grit top, clipped to galvanized stringers. Isophthalic polyester was selected because the exposure is ore dust, alkaline seepage and UV rather than strong acid or solvent. Standard moulded panels ship at 1220 by 3660 mm; the 38 mm full panel weighs about 87 kg. Every clip is SS316, never carbon steel, so the fasteners do not become the first point of failure on a remote site.

Installation and field practice

Panels are cut to net size at the Nantong factory to the existing support spacing, with pre-cut openings around the transfer chute, idler access and the decant valve. On site the crew only does light fitting around brackets and stringers. Each panel is fixed with SS316 clips at every support, and the factory seals every cut edge with matching resin so moisture and alkaline seepage cannot wick into the glass fibres.

Installation follows standard field practice: panels are staged by bay on the pad, lifted by two fitters, dropped onto the stringers and clipped down. No welding, no grinding and no hot-work permit is required. Handrail and toe-kick, where present, follow the existing steel layout and are fixed with the same SS316 hardware. Spare panels are pre-cut to the same size so a damaged section swaps in with hand tools during a scheduled shutdown.

Delivery scope, acceptance and observed service

This page does not disclose the project area, piece count, customer name, contract value or completion year. The following is the delivery scope and the acceptance focus rather than a quantified outcome claim.

Delivery scope: 50 mm pultruded I-bar panels on the screening walkway and over-belt platform, 38 mm moulded isophthalic panels on the 80 m tailings path, all with SS316 clips and factory-sealed edges. Technical targets met: open mesh lets ore dust fall through instead of packing; grit and concave surfaces remain non-slip when the deck is damp; the lightweight panels cleared the existing supports without structural modification. Acceptance focus at handover was clip torque on every support, sealed cut edges, non-slip surface underfoot, and fit-up around chutes and idlers. In-service observation reported on the page: three years after installation none of the three routes has been blasted, recoated or re-clipped, and the mine has stopped flying in welders for grating repairs on remote shutdowns.

Common failure modes in this industry and how to prevent them

1. Heavy haul truck and loader impact on secondary walkways cracks the bar cross-section at the bearing point.

A cracked bar propagates along the whole length under repeated traffic; the panel then sags and must be replaced.

Use 50 mm panels (27 kg/m2) on primary haul routes, 38 mm on secondary access. Design for 5 kN/m2 point load at clips. Avoid 25 mm panels on any walkway that sees mobile plant.

2. Abrasive ore dust and slurry wear the grit top flat, turning the surface smooth and slippery under wet boots.

A smooth GRP surface reaches <0.4 COF when wet, causing slips. Worn bars also lose the resin-rich layer and expose fibres.

Specify a 1.5 mm grit-aggregate top (silicon carbide or quartz). Schedule replacement when the grit is worn below 0.5 mm. Annual friction test with a pendulum tester.

3. Dust loading on horizontal bars builds up over 6-12 months, adding dead load and trapping moisture against the bar.

A 10 mm dust layer on a 900 mm span adds 0.15 kN/m2. Combined with moisture, it accelerates under-bar corrosion of clips.

Design cleaning access every 6 months. Specify open-mesh (not closed-top) panels for dust areas so material falls through. Clip rows must be reachable for inspection.

4. Haul-road vibration loosens clips over time; panels shift and create trip edges.

A shifted panel can lift 10-15 mm at the edge, tripping operators. In extreme cases the panel slides off the support.

Use SS316 double-clip (two per bearing bar) on vibrating routes. Re-torque to 5 N m at 3 and 6 months. Add anti-lift tabs where panels are horizontal.

Failure mode Trigger condition Prevention parameters
Impact cracking Haul truck / loader near walkway 50 mm primary, 38 mm secondary; 5 kN/m2 point
Grit wear / slip Ore dust + slurry, wet boots 1.5 mm carbide grit; pendulum test; replace <0.5 mm
Dust overload Horizontal bars, 6-12 months Open mesh; 6-month cleaning; accessible clips
Clip loosening Haul-road vibration SS316 double-clip; re-torque 3/6 months; anti-lift

Related products and project references

The screening and conveyor routes draw on the pultruded I-bar product family for longer spans, while the tailings path uses the moulded isophthalic range for general anti-slip duty. SS316 clips and edge-sealing resin are the standard hardware across all three routes. For a new Pilbara-style enquiry the technical team asks first for the support spacing and the seepage chemistry, then recommends thickness and surface; minimum order is 10 square metres and lead time runs 12 to 36 working days depending on resin and thickness.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com