FRP Grating for SA Concentrators, Thickener Platforms and Reagent Zones

Project Case Studies
Direct Answer

For South African mining and metallurgy sites we specify vinyl ester FRP grating on concentrator walkways, thickener clarifier platforms and reagent dosing areas. The panels handle acidic process water, reagent splash and Highveld UV, carry 12 kN/m2 at 900 mm, and clip down with SS316 fasteners so crews work without a hot-work permit on a busy plant.

  • Best for: Concentrator walkway, thickener platform, reagent area
  • Specify when: Vinyl ester resin, 38 mm molded, grit top
  • Key spec: 38 mm vinyl ester, 19.5 kg/m2, 12 kN/m2 at 900 mm, SS316

A South African concentrator on the Highveld had been replacing steel grating on three routes every three years. Acidic process water, flotation reagent splash and Highveld UV all attacked the zinc coating from below. We supplied 38 mm molded vinyl ester panels with grit tops, cut to the existing support spacing and fixed with SS316 clips. Two and a half years on, none of the three areas has been blasted, recoated or re-clipped, and the plant has stopped booking hot-work windows for grating repairs during shutdowns.

Site conditions and the three project cases

Why steel fails on a South African concentrator

Painted steel grating on a South African metallurgical plant rarely lasts beyond three to five years. Acidic process water from the flotation circuit drips onto the underside of the deck, and reagent splash strips the coating within months. Highveld UV and winter frost cycles embrittle the zinc, and washdown water after mill relines sits on the top surface. By year three the bar ends pit, the stringers rust and the plant books another hot-work outage. The acidic water, reagent splash and UV combination is what kills steel on the concentrator floor.

Case 1: walkway on the concentrator floor

The concentrator floor walkway runs around the ball mills and flotation banks where operators check the cell levels twice an hour. Acidic process water and reagent splash cover the deck, so painted steel rusts from the top down. We installed 38 mm molded vinyl ester panels with a grit top, spanning 900 mm between the existing steel supports and clipped with SS316 fasteners. The open mesh lets drips fall into the trench below, and the grit stays non-slip even when the deck is wet with slurry. Cell operators report less slipping during winter mornings than they had on the old polished steel.

Case 2: platform on the thickener clarifier

The thickener clarifier platform sits on top of the rake thickener where operators walk to the drive unit and the overflow launder. Acidic process water and mist cover the deck, and steel here was blasted and recoated every two years, but the recoat required tank access permits. We supplied 38 mm molded vinyl ester panels with a concave surface, pre-cut around the drive housing and the launder outlet. The panels weigh about a quarter of steel at equal stiffness, so the existing thickener curb carried them without modification. The last shutdown needed zero hot work on the grating, which let the thickener return to service a day early.

Case 3: walkway in the reagent dosing area

The reagent dosing area walkway runs along the dosing pumps where operators add flotation reagents and pH modifiers. Concentrated acid and caustic splash the deck on every refill, and mild steel clip holes corrode within two years. We laid 38 mm molded vinyl ester panels with a smooth top, clipped to stainless steel supports with SS316 fasteners. The smooth face wipes clean with a single hose-down, and the vinyl ester resists acid and caustic that would eat through isophthalic. The walkway has gone through two refill cycles with no pitting at the clip holes at all.

Product selection, maintenance and specifications

Product types and resin selection

Vinyl ester was the right resin here because the site sees acidic process water, reagent splash and caustic rather than just outdoor UV. Isophthalic would have been cheaper but would not hold up to repeated acid and caustic contact. For longer thickener spans we would have moved to 50 mm pultruded I-bar, which weighs 15 to 17 kg/m2 and clears wider gaps. Surfaces follow duty: grit top for the concentrator walkway, concave for the thickener deck, smooth for the reagent area. Every clip is SS316, never carbon steel, so the fasteners do not become the failure point.

Maintenance and service life

Maintenance is limited to a weekly hose-down with fresh water to wash reagent splash off the grit, and an annual walk-around to check clip torque and the sealed cut edges. The factory seals every edge so acid and caustic cannot wick into the glass fibers. We expect 20 plus years of service on the thickener and reagent areas, and 15 to 20 years on the concentrator floor, against three to five years for painted steel. Spare panels are pre-cut to the same size, so a damaged section swaps in with hand tools during a planned shutdown. No blasting, no recoating, no hot-work permit is needed to keep the deck in service.

How to start your project

To quote a South African metallurgical project we need three inputs. First, a sketch with support spacing, thickener diameter and the width of the walkway or platform. Second, the reagent and process water list the deck will contact directly, including concentrations and pH. Third, the loading case, whether operators with tools or hand-truck traffic. We come back with a load-table check against the m38 rating of 12 kN/m2 at 900 mm, a vinyl ester recommendation, and surface swatches for site testing. Our Nantong plant has exported to 45 plus countries for 20 plus years. Send the reagent list and the support spacing first; the resin and thickness follow from those two.

Standard specifications and delivery

Standard molded panels ship at 1220 by 3660 mm and we cut them to net size at the factory, so the on-site crew only does light fitting around pumps and launders. Thickness options cover 25, 30, 38, 50 and 65 mm, with the 65 mm panel at 38 kg/m2 for heavy zones. The minimum order is 10 m2, and lead time runs 12 to 36 working days depending on resin and thickness. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. Each shipment carries the ISO 9001 certificate numbered 01708Q11888R0S and the ASTM F3059 report numbered 211122012SHF-001, with SGS inspection on request. Panels are bundled by plant area and labeled by cell so the installer can stage them on the floor without a crane.

Key takeaways

Three points sum up this South African concentrator job. First, the painted-steel replacement cycle of three years is gone; the vinyl ester panels are now in year two and a half with zero recoating. Second, the 38 mm vinyl ester panels clear the 900 mm span at 12 kN/m2, which is the rating most concentrator and thickener platforms need. Third, SS316 clips and factory-sealed edges remove the two points that used to corrode first. If you are rebuilding a thickener platform or a reagent walkway, start with the reagent list and the support spacing, and the rest follows.For the technical background see Acid-resistant FRP grating for South African platinum mining and Compare resin chemical resistance across 50 plus chemicals.
Which resin handles acidic process water and reagent splash?
Vinyl ester is the standard call here; isophthalic handles UV but not repeated acid and caustic. We back it with the ASTM F3059 report numbered 211122012SHF-001.
Can a panel be swapped during a planned shutdown without welding?
Yes. Panels clip on with SS316 fasteners and need no welding, so two fitters lift out a section during a shutdown with hand tools.
What lead time applies to a vinyl ester metallurgical order?
Standard vinyl ester 38 mm panels ship in 12 to 36 working days depending on thickness, with a minimum order of 10 m2 and ISO 9001 certificate 01708Q11888R0S attached.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026|Category: Project Case Studies|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Marine Offshore Projects
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Project background

The case covers a South African concentrator on the Highveld where painted steel grating on three routes was being replaced on a three-year cycle. The three routes are the walkway on the concentrator floor around the ball mills and flotation banks, the platform on top of the rake thickener, and the walkway in the reagent dosing area.

Acidic process water from the flotation circuit drips onto the underside of the deck, reagent splash strips the coating within months, and Highveld UV with winter frost cycles embrittles the zinc. Washdown water after mill relines sits on the top surface. The customer asked for a corrosion-resistant alternative that could be fitted during a busy shutdown without booking hot-work windows for grating repairs.

Specifications and load ratings

All three routes are supplied as 38 mm moulded vinyl ester panels. The concentrator floor walkway uses a grit top, the thickener platform uses a concave surface, and the reagent dosing walkway uses a smooth top. The panels span 900 mm between the existing supports and are rated for 12 kN per square metre at that span, the personnel-with-tools load class most concentrator and thickener platforms require.

Vinyl ester was selected because the site sees acidic process water, reagent splash and caustic refill rather than outdoor UV alone; isophthalic would have been cheaper but would not hold up to repeated acid and caustic contact. The 38 mm moulded panel weighs about 19.5 kg per square metre, roughly a quarter of steel at equal stiffness, so the existing thickener curb and steel stringers carried the panels without modification. Standard moulded panels ship at 1220 by 3660 mm. Every clip is SS316, never carbon steel, and every cut edge is factory-sealed with vinyl ester resin.

Installation and field practice

Panels are cut to net size at the Nantong factory to the existing support spacing, with pre-cut openings around the drive housing, the launder outlet, the dosing pumps and the pH modifier skid. On site the crew only does light fitting around pumps and launders. Each panel is fixed with SS316 clips at every support, and the factory seals every cut edge so acid and caustic cannot wick into the glass fibres.

Installation follows standard field practice: panels are staged by plant area on the floor, lifted by two fitters, dropped onto the stringers and clipped down. No blasting, no recoating and no hot-work permit is required. Handrail and toe-kick, where present, follow the existing layout. Spare panels are pre-cut to the same size so a damaged section swaps in with hand tools during a planned shutdown.

Delivery scope, acceptance and observed service

This page does not disclose the project area, piece count, customer name, contract value or completion year. The following is the delivery scope and the acceptance focus rather than a quantified outcome claim.

Delivery scope: 38 mm moulded vinyl ester panels on the concentrator floor walkway, the thickener clarifier platform and the reagent dosing walkway, all with SS316 clips and factory-sealed edges. Technical targets met: open mesh lets acidic drips fall into the trench below; grit, concave and smooth surfaces match each duty; the smooth reagent face wipes clean with a single hose-down. Acceptance focus at handover was clip torque on every support, sealed cut edges, surface finish per area, and fit-up around pumps, launders and drive housings. In-service observation reported on the page: two and a half years after installation none of the three areas has been blasted, recoated or re-clipped, and the plant has stopped booking hot-work windows for grating repairs during shutdowns.

Common failure modes in this industry and how to prevent them

1. Heavy haul truck and loader impact on secondary walkways cracks the bar cross-section at the bearing point.

A cracked bar propagates along the whole length under repeated traffic; the panel then sags and must be replaced.

Use 50 mm panels (27 kg/m2) on primary haul routes, 38 mm on secondary access. Design for 5 kN/m2 point load at clips. Avoid 25 mm panels on any walkway that sees mobile plant.

2. Abrasive ore dust and slurry wear the grit top flat, turning the surface smooth and slippery under wet boots.

A smooth GRP surface reaches <0.4 COF when wet, causing slips. Worn bars also lose the resin-rich layer and expose fibres.

Specify a 1.5 mm grit-aggregate top (silicon carbide or quartz). Schedule replacement when the grit is worn below 0.5 mm. Annual friction test with a pendulum tester.

3. Dust loading on horizontal bars builds up over 6-12 months, adding dead load and trapping moisture against the bar.

A 10 mm dust layer on a 900 mm span adds 0.15 kN/m2. Combined with moisture, it accelerates under-bar corrosion of clips.

Design cleaning access every 6 months. Specify open-mesh (not closed-top) panels for dust areas so material falls through. Clip rows must be reachable for inspection.

4. Haul-road vibration loosens clips over time; panels shift and create trip edges.

A shifted panel can lift 10-15 mm at the edge, tripping operators. In extreme cases the panel slides off the support.

Use SS316 double-clip (two per bearing bar) on vibrating routes. Re-torque to 5 N m at 3 and 6 months. Add anti-lift tabs where panels are horizontal.

Failure mode Trigger condition Prevention parameters
Impact cracking Haul truck / loader near walkway 50 mm primary, 38 mm secondary; 5 kN/m2 point
Grit wear / slip Ore dust + slurry, wet boots 1.5 mm carbide grit; pendulum test; replace <0.5 mm
Dust overload Horizontal bars, 6-12 months Open mesh; 6-month cleaning; accessible clips
Clip loosening Haul-road vibration SS316 double-clip; re-torque 3/6 months; anti-lift

Related products and project references

All three routes draw on the moulded vinyl ester product family for acid and caustic resistance; for longer thickener spans the same family moves up to 50 mm pultruded I-bar, which weighs about 15 to 17 kg per square metre. SS316 clips and vinyl ester edge-sealing resin are the standard hardware across the routes. For a new Highveld-style enquiry the technical team asks first for the reagent list with concentrations and pH, and the support spacing; minimum order is 10 square metres and lead time runs 12 to 36 working days depending on resin and thickness.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com