25x100 Molded FRP Grating
Rectangular 1x4 mesh favoring drainage and air flow while keeping a firm walking surface.
Technical specifications
| Type | Molded FRP grating |
|---|---|
| Mesh opening | 25 x 100 mm (1 x 4 in) |
| Thickness options | 25, 30, 38, 40, 50 mm |
| Standard panel size | 1220 x 3660 mm (4 x 12 ft), cut to size |
| Typical open area | about 65-72% (typical) |
| Resin systems | Orthophthalic polyester (IS), Fire-retardant polyester (IF), ASTM E84, Vinyl ester (VE) |
| Surface options | Concave top, Grit anti-slip, Smooth |
Load and span guidance
As with other molded panels, span and load capacity are verified to DIN 24537-3 against thickness and support spacing; refer to the load table for the governing point and uniform loads.
Typical applications
- Cooling towers
- Air intake and ventilation
- Drainage and trench covers
- Marine and offshore decks
Sizing, installation and procurement
The mesh opening of 25 x 100 mm (1 x 4 in) is not a detail — it is the main sizing decision. At about 65-72% (typical) open area the deck drains water, oil and swarf quickly while staying closed enough for safety footwear. Where small tools, screws or heels must not drop through, the next smaller mesh is the right answer; where ventilation or wash-down action matters more, this opening is kept and the supports are checked instead.
Mesh and real use
Two panels of the same depth do not behave alike once the mesh changes: a wider opening spreads a point load over fewer bars. For pallet trucks, forklifts or a heavily used workshop floor, the load table is read at the real span — not the depth alone — against the deflection limit, usually L/200 on walkable decks. We run that check against your drawing and state the allowable span between supports before you order.
Depth, load and span
This reference is produced in 25, 30, 38, 40, 50 mm mm. Adding depth buys stiffness as much as strength: the right move when the span has to grow without an intermediate bearer, or when the area is crossed by heavy plant. The thinner option stays cheaper on short spans without giving away safety.
Resins and finishes
Resin options are Orthophthalic polyester (IS), Fire-retardant polyester (IF), ASTM E84, Vinyl ester (VE). Finishes: Concave top, Grit anti-slip, Smooth. Vinyl ester is the choice for acids, alkalis and chlorides; fire-retardant polyester to ASTM E-84 for areas under a fire requirement; orthophthalic polyester remains the economical standard. The concave (meniscus) top holds water and oil inside the mesh and grips better when wet; the gritted version suits ramps, stairs and busy outdoor areas; the smooth top makes wash-down easier in food and pharma rooms.
Cutting and fixing
Standard panel 1220 x 3660 mm (4 x 12 ft), cut to size, cut in the works to drawing with deburred edges. Fix with M, C, L or Z clips and stainless bolts; on trafficked or wind-exposed decks, add through-bolting at the corners. Production is 15-25 days for standard sizes, 12-36 working days end to end, from 10 m², with single-piece samples available. For project cuts we issue a packing list with weight and bundle sizes so freight can be quoted before shipment.
Plant and documentation
Made in our own plant in Nantong: 20,000 m², 200+ staff, in production since 2004. The company holds ISO 9001 and has its products tested to ASTM E-84 and ASTM F3059, with ABS, Intertek and SGS documentation on file and CE marking on the product. Certificates and test reports are provided on request.
Technical data sheets (PDF)
- frp-molded-grating-specifications.pdf (297 KB, PDF)
- molded-frp-grating-technical-manual.pdf (1647 KB, PDF)
- frp-grating-load-table.pdf (4 KB, PDF)
Data sheets carry no certificate numbers; full test reports are sent on request.
