Heavy-Duty I-Bar Pultruded Grating
Reinforced I-bar sections for the heaviest industrial loads and wider spans.
Technical specifications
| Type | Pultruded FRP grating |
|---|---|
| Mesh opening | 38 x 38 / 25 x 50 mm, heavy-duty I-bar |
| Thickness options | 40, 50, 65 mm |
| Standard panel size | up to 1220 x 6096 mm (4 x 20 ft), cut to size |
| Typical open area | about 60-68% (typical) |
| Resin systems | Polyester (IF), Vinyl ester (VE), Polyurethane (PU) |
| Surface options | High-load I-bar, gritted, Gritted anti-slip |
Load and span guidance
Heavy I-bar sections are selected for elevated point and rolling loads over wider support spacing; the governing loads and deflection limits are verified from the load table for the specific span.
Typical applications
- Heavy plant and maintenance platforms
- Vehicular and trolley access
- Mining and heavy industry
- Wide-span mezzanines
Sizing, installation and procurement
The mesh opening of 38 x 38 / 25 x 50 mm, heavy-duty I-bar is not a detail — it is the main sizing decision. At about 60-68% (typical) open area the deck drains water, oil and swarf quickly while staying closed enough for safety footwear. Where small tools, screws or heels must not drop through, the next smaller mesh is the right answer; where ventilation or wash-down action matters more, this opening is kept and the supports are checked instead.
Mesh and real use
Two panels of the same depth do not behave alike once the mesh changes: a wider opening spreads a point load over fewer bars. For pallet trucks, forklifts or a heavily used workshop floor, the load table is read at the real span — not the depth alone — against the deflection limit, usually L/200 on walkable decks. We run that check against your drawing and state the allowable span between supports before you order.
Depth, load and span
This reference is produced in 40, 50, 65 mm mm. Adding depth buys stiffness as much as strength: the right move when the span has to grow without an intermediate bearer, or when the area is crossed by heavy plant. The thinner option stays cheaper on short spans without giving away safety.
Resins and finishes
Resin options are Polyester (IF), Vinyl ester (VE), Polyurethane (PU). Finishes: High-load I-bar, gritted, Gritted anti-slip. Vinyl ester is the choice for acids, alkalis and chlorides; fire-retardant polyester to ASTM E-84 for areas under a fire requirement; orthophthalic polyester remains the economical standard. The concave (meniscus) top holds water and oil inside the mesh and grips better when wet; the gritted version suits ramps, stairs and busy outdoor areas; the smooth top makes wash-down easier in food and pharma rooms.
Cutting and fixing
Standard panel up to 1220 x 6096 mm (4 x 20 ft), cut to size, cut in the works to drawing with deburred edges. Fix with M, C, L or Z clips and stainless bolts; on trafficked or wind-exposed decks, add through-bolting at the corners. Production is 15-25 days for standard sizes, 12-36 working days end to end, from 10 m², with single-piece samples available. For project cuts we issue a packing list with weight and bundle sizes so freight can be quoted before shipment.
Plant and documentation
Made in our own plant in Nantong: 20,000 m², 200+ staff, in production since 2004. The company holds ISO 9001 and has its products tested to ASTM E-84 and ASTM F3059, with ABS, Intertek and SGS documentation on file and CE marking on the product. Certificates and test reports are provided on request.
Technical data sheets (PDF)
- frp-heavy-duty-grating-catalogue.pdf (594 KB, PDF)
- frp-pultruded-grating-specification.pdf (21736 KB, PDF)
- frp-pultruded-grating-catalogue.pdf (26 KB, PDF)
- frp-grating-load-table.pdf (4 KB, PDF)
Data sheets carry no certificate numbers; full test reports are sent on request.
