FRP Grating on a North Sea Platform: Splash Zone, Deck and Stair

Project Case Studies
Direct Answer

North Sea platforms put salt spray, process vapors and chlorinated wash water on the same panel. Vinyl ester FRP grating survives the mix without painting, without hot-work permits and without a recurring corrosion inspection cycle that the O&M budget and the offshore schedule can no longer carry.

  • Best for: Splash-zone walkways, process deck platforms, access stair treads
  • Specify when: Vinyl ester, 38 mm molded and 50 mm pultruded, grit top and concave
  • Key spec: 38 mm vinyl ester, 19.5 kg/m2, 12 kN/m2 at 900 mm, SS316 clips

A North Sea production platform ran galvanized steel grating on three routes: the boat landing walkway in the splash zone, a small process deck around a separator skid, and the access stair to the cellar. Steel held four years on the walkway before pitting took over, then the operator faced a recurring hot-work permit for every swap, each one booked into the quarterly turnaround. We supplied vinyl ester FRP grating on all three routes, and none of them needs repainting, rust inspection or a hot-work permit now.

Site conditions and the three project cases

Why steel fails on a North Sea platform

On a North Sea platform, steel grating meets salt spray in the splash zone, intermittent hydrocarbon vapors in the process area, and deck drainage mixed with chlorinated wash water. Galvanized steel loses its zinc in three to four years; painted steel chips at tool drop points and underfilm corrosion spreads underneath. A failed panel cannot be swapped on a normal permit because hot work is banned offshore, so panels stay in service past their safe life. Splash-zone steel typically needs replacement at year four or five, and each swap costs a shutdown window and a permit we would rather avoid.

Case 1: splash-zone walkway to the boat landing

Along the splash-zone railing, operators walk out to the boat landing and the mooring deck every shift. We supplied 38 mm molded FRP grating in vinyl ester resin with grit top surface, 900 mm support span, clipped to existing steel stringers with SS316 clips. Vinyl ester was chosen because the panel lives where salt spray hits it directly and where helideck wash water drains past it. Grit top keeps boots planted when the deck is wet from spray, and the panel weighs 19.5 kg per square meter, so two technicians can lift a replacement segment over the railing without a crane.

Case 2: removable process deck platform

On the process deck around a separator skid, maintenance needed a small platform to reach flange level without a scaffold. We supplied 25 mm molded grating with concave surface as removable sections, each under 25 kg, clipped to the skid frame. Concave drains wash water off quickly and is easier to sweep than grit, which suits a platform occupied only during planned maintenance. Because FRP is non-sparking and non-conductive, the platform can be clipped around energized instrumentation without a hot-work permit, cutting a two-day scaffold window to a half-day clip-in.

Case 3: access stair treads to the cellar

The access stair between drill floor level and the process cellar wore steel treads smooth in two years. We supplied pultruded I-profile grating, 50 mm deep, in vinyl ester, cut to stair-width treads with nosing, fixed with SS316 clips to the existing stringers. Pultruded treads carry the point load of a tool bag and boots without permanent deflection, and the grit nosing stays visible under deck lighting. The stair now carries the same foot traffic it did in steel, with no rust bleed running down the stringers below.

Product selection, maintenance and specifications

Product types and resin selection

Across the three locations the material follows the service condition. Splash zone and wash-down areas take vinyl ester molded 38 mm with grit top; light maintenance platforms take 25 mm concave; long stair spans take pultruded I-profiles at 50 mm depth. Isophthalic polyester stays out of splash service because salt water and UV degrade it faster offshore. Clips are always SS316, never carbon steel, and cut edges are sealed with matching resin so salt cannot wick into the fibers. Where fire load is high, we can switch to phenolic resin for low-smoke accommodation-deck routes.

Maintenance and service life

Offshore FRP needs no painting and no rust inspection. Each year during a planned stop, technicians walk the panels, check clip torque, and rinse salt residue from the undersides with fresh water. Cut edges are checked for chipped resin, and a touched-up edge seal takes minutes. Expected service life in splash and process zones is 20 years or more, against four to eight years for galvanized steel in the same exposure. Replacement segments are pre-cut to panel dimensions in Nantong and shipped flat-packed, so a swap uses a normal work permit and no hot work.

How to start your project

A quote starts with three inputs: a sketch showing panel sizes and support spans, the process fluids or wash chemistry the panels will see, and the required surface and load rating. We then check the span against the load table, recommend resin and thickness, and send sample coupons of the target surface so the offshore team can judge slip resistance under boot tread. For Norwegian operators we pack NORSOK-facing documentation alongside the ISO 9001 certificate and the ASTM F3059 report, because the site audit will ask for both.

Standard specifications and delivery

Standard molded panels ship at 1220 by 3660 mm, in 25, 30, 38, 38x40, 50 and 65 mm depths, with 38x38 or 50x50 mesh. Pultruded T and I profiles come in 25, 38, 50 and 76 mm depths. MOQ is 10 m2 and lead time runs 12 to 36 working days depending on resin and profile. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. Each order ships with ISO 9001 certificate 01708Q11888R0S, the ASTM F3059 test report 211122012SHF-001, and SGS reports on request. Panels are banded into lift-friendly packs so a deck crane moves them without a spreader.

Key takeaways

Three points close the case. First, splash-zone steel that fails in four years is replaced by vinyl ester FRP rated for 20 years or more, which removes a recurring hot-work permit. Second, process deck platforms and stair treads do not need heavier steel when 25 mm molded and 50 mm pultruded FRP cover the same spans at a quarter of the weight. Third, 38 mm molded at 19.5 kg per square meter carries 12 kN per square meter at 900 mm span, the load class most offshore walkways actually require.For the technical background see NORSOK-facing FRP grating for North Sea work and Saltwater- and fire-rated FRP offshore.
Does FRP grating meet offshore fire rules?
With fire-retardant additive the isophthalic or vinyl ester system reaches ASTM E84 Class 1, and phenolic resin is available for low-smoke accommodation routes. We supply the test report with the shipment.
Can replacement panels be lifted over the railing without a crane?
Yes. A 38 mm molded panel weighs 19.5 kg per square meter, and we cut segments small enough that two technicians carry one over the railing without hot work or a deck crane.
What load does 38 mm molded FRP carry at 900 mm span?
M38 molded carries 12 kN per square meter at 900 mm span, which covers personnel walkways with tool bags. For forklift loads we move to 65 mm molded or 50 mm pultruded profiles.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026|Category: Project Case Studies|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating for Offshore & Marine
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Project background

The case covers a North Sea production platform where galvanized steel grating on three routes was pitting out within four years. The three routes are the boat-landing walkway in the splash zone, a removable process deck platform around a separator skid, and the access stair treads between drill floor level and the process cellar.

Splash-zone steel meets salt spray, process vapours and deck drainage mixed with chlorinated wash water. Hot work is banned offshore, so a failed panel cannot be swapped on a normal permit and panels stay in service past their safe life. The operator asked for a non-painting, non-sparking, non-conductive alternative that could be clipped in during a planned stop without a hot-work window.

Specifications and load ratings

The splash-zone walkway uses 38 mm moulded vinyl ester panels with a grit top, spanning 900 mm on existing steel stringers. The removable process deck uses 25 mm moulded panels with a concave surface, each section kept under 25 kg so two technicians can lift it. The access stair uses 50 mm pultruded I-profile treads with grit nosing, fixed to the existing stringers.

The 38 mm moulded panel weighs about 19.5 kg per square metre and is rated for 12 kN per square metre at 900 mm span, the personnel-with-tool-bag load class most offshore walkways require. Vinyl ester was selected for splash and wash-down service; isophthalic stays out of splash service because salt water and UV degrade it faster offshore. Standard moulded panels ship at 1220 by 3660 mm in 25, 30, 38, 38x40, 50 and 65 mm depths; pultruded T and I profiles come in 25, 38, 50 and 76 mm depths. Every clip is SS316 and every cut edge is sealed with matching resin.

Installation and field practice

Panels are cut to net size at the Nantong factory, with pre-cut openings around the skid frame, the railing line and the stair stringers. On board the crew only does light fitting around the skid frame and the railing base. Each panel is fixed with SS316 clips at every support; the removable process deck sections clip on and off so maintenance can lift them away without tools beyond a spanner.

Installation follows standard offshore practice: panels are banded into lift-friendly packs so a deck crane moves them without a spreader. Because FRP is non-sparking and non-conductive, the process deck can be clipped around energised instrumentation without a hot-work permit. Stair treads are clipped to the existing stringers with the same SS316 hardware, and the grit nosing stays visible under deck lighting. Replacement segments are pre-cut to panel dimensions and shipped flat-packed.

Delivery scope, acceptance and observed service

This page does not disclose the project area, piece count, operator name, contract value or completion year. The following is the delivery scope and the acceptance focus rather than a quantified outcome claim.

Delivery scope: 38 mm moulded vinyl ester grit panels on the splash-zone boat-landing walkway, 25 mm moulded concave removable sections on the process deck around the separator skid, and 50 mm pultruded I-profile treads on the cellar access stair, all with SS316 clips and factory-sealed edges. Technical targets met: panels survive salt spray and chlorinated wash water without painting; non-sparking and non-conductive material lets maintenance clip around energised instrumentation; removable sections lift off by hand without a scaffold. Acceptance focus at handover was clip torque on every support, sealed cut edges, grit nosing visibility, and lift weight of removable sections. Expected service life in splash and process zones is 20 years or more, against four to eight years for galvanized steel in the same exposure.

Common failure modes in this industry and how to prevent them

1. Salt-laden air and splash wetting expose glass fibres (whitening) on the gel-coat within 2-3 years if the resin-rich top veil is too thin.

Exposed fibres absorb water, raising moisture from 0.5% to over 3%, triggering osmotic blistering. Flexural strength drops 20-30% before any visible crack.

Specify a minimum 0.4 mm resin-rich C-veil on all walkway panels. Reject panels where grit top shows bare fibre within 1 m. Acceptance: Barcol hardness ≥40.

2. UV degradation in open sun fades the gel-coat to chalky white and embrittles the surface within 5-7 years.

Embrittled surfaces crack under walking loads, hold water in micro-cracks and accelerate fibre exposure.

Specify isophthalic resin with UV inhibitor for permanently exposed decks. Re-gel-coat every 5 years in high-UV zones. Avoid orthophthalic resin in marine service.

3. SS304 or even SS316 clips in seawater splash suffer pitting and crevice corrosion; aluminium handrails couple galvanically with GRP.

A pitted clip snaps under load. Galvanic corrosion eats the bar cross-section at the contact within 3 years.

Use SS316 clips and fasteners only. Isolate aluminium handrails from GRP with nylon washers. Never use carbon-steel fixings in splash zone. Annual rope-access clip inspection.

4. Splash-zone wave impact and floating debris strike thinner 25-30 mm panels on secondary access.

Impact cracks the bar, and water ingress turns the crack white along the whole bar within months.

Use 38 mm minimum in splash zone, 50 mm where debris impact is known. Add a 50 mm solid cover over berthing areas. Design for 5 kN/m2 point load at clips.

Failure mode Trigger condition Prevention parameters
Fibre exposure (whitening) Splash zone, thin gel-coat 0.4 mm C-veil; Barcol ≥40; reject bare fibre
UV embrittlement Open deck, 5-7 years sun Isophthalic + UV inhibitor; re-gel-coat 5 y
Clip pitting / galvanic Seawater splash, SS304 clips SS316 only; nylon isolation; annual inspection
Impact cracking Wave / debris in splash zone 38 mm min, 50 mm at berth; 5 kN/m2 point

Related products and project references

The splash-zone and stair routes draw on the moulded and pultruded vinyl ester product families for salt-water resistance; the removable process deck uses the lighter 25 mm moulded range for maintenance-only duty. SS316 clips, vinyl ester edge-sealing resin and FRP handrail systems are the standard hardware across the routes. For a new North Sea-style enquiry the technical team asks first for panel sizes and support spans, the process fluids or wash chemistry, and the required surface and load rating; minimum order is 10 square metres and lead time runs 12 to 36 working days depending on resin and profile.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com