📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
GRP Structural Profiles · Pultruded to BS EN 13706 · Bearers for GRP Grating Decks

GRP Structural Profiles

Pultruded GRP I-beams, channels, angles, square tube, rod and flat sheet — the support structure that lets a GRP grating panel span further than it can on its own. Specified to BS EN 13706 grade E17 and E23, with the load and deflection data an engineer needs to sign it off.

BS EN 13706E17 / E23 GradesISO 900145+ CountriesCut to Length
Definition

What GRP Structural Profiles Are

A GRP structural profile is a constant-section composite member produced by pultrusion — glass reinforcement pulled continuously through a resin bath and a heated die, so the fibres run lengthwise and the strength runs with the load. It is the structural half of a GRP deck; the grating panel is the walking surface on top of it.

The distinction that matters commercially is between a profile and a panel. A GRP grating panel is a moulded or pultruded open-mesh product, and its span is limited by its own section depth — typically around 1.2 m before deflection becomes uncomfortable. A GRP structural profile is a solid-section member that carries load over metres, and it exists so that the deck above it can be built at a height where a person needs to walk.

That is why the two are almost always bought together. A platform specification that names a 38 mm grating panel but leaves the bearer to someone else is an incomplete specification, and it usually resolves itself on site as a deck that deflects because the support was chosen for price rather than for span.

Terminology on this page: GRP structural profiles, GRP pultruded profiles, GRP beams and GRP bearers all describe the same family. FRP, fibreglass profiles and composite profiles are the same product under its North American name. What changes between the terms is the standard cited and the market convention, not the member.

Range

The Profile Shapes and What Each One Is For

I

GRP I-Beam

The most efficient shape per kilogram for bending, because the flanges carry the moment and the web carries the shear. Used as the primary bearer under a grating deck, and as the beam in a GRP walkway or platform frame where depth is available.

C

GRP Channel

Two flanges and one web. Half the bending efficiency of an I-beam at the same depth, but far easier to bolt through a web and to build into a frame edge. The default choice for platform stringers and for the perimeter of a deck.

A

GRP Angle

Equal and unequal leg angles for edge trim, corner reinforcement and stair stringers. Small, cheap and the profile most often forgotten from a take-off until the deck edge needs a finish.

T

GRP Square and Rectangular Tube

Closed section with torsional stiffness an open profile cannot match. Used for handrail posts, frame members and anywhere the member is loaded in more than one direction.

R

GRP Rod

Solid round bar, typically for machined parts, hinge pins and locations where a bolted connection needs a composite insert rather than a steel one.

F

GRP Flat Sheet and Plate

For bearer plates, connection shims, cut-to-shape parts and the flat sections that a fixing detail often needs but a take-off rarely lists.

Standards

BS EN 13706 and the Grade That Matters

BS EN 13706 is the European standard for pultruded profiles, and it defines grades by measured mechanical property rather than by a supplier's description. A profile sold as "high strength" without a grade is a profile with no declared property, and an engineer cannot check it against a load case.

GradeWhat it declaresWhere it is usedWhat to ask for
E17The standard structural grade, with declared tensile, flexural and compressive propertiesMost platform bearers, stringers, handrail posts and general structural framingThe grade on the datasheet, stated as E17 to BS EN 13706, not as "structural grade"
E23The higher-modulus grade, achieved with a higher glass content and a tighter processLong spans, high load cases and where deflection is the governing limit rather than strengthBoth the grade and the measured modulus, since the modulus is what decides deflection

The practical point: GRP is stiffness-limited far more often than it is strength-limited. A GRP beam will usually carry the load long before it stops deflecting acceptably, so the number that decides the section is the modulus of elasticity, not the ultimate strength. A supplier who quotes only a strength figure has answered the question nobody was asking.

One honest note on certification: BS EN 13706 covers the pultruded profile and is the real, checkable standard for this product. It is not a CE marking route for the member, and it is not the same as BS 4592, which covers grating and treads. A supplier who conflates the two is either confused or hoping you are.

Integration

Using GRP Profiles as Bearers Under GRP Grating

This is the application that brings most buyers to a structural profile in the first place, so it is worth setting out how the two products actually fit together.

  • Bearer spacing sets the panel span. A 38 mm moulded panel is comfortable at 900 mm and marginal at 1,200 mm. A 50 mm panel buys more span but not unlimited span. Bearer centres are the design decision that makes the panel work.
  • Panels do not span; bearers span. Where a deck needs to clear a trench, a duct or a walkway of 2 m or more, the panel sits on bearers and the bearers do the spanning. Adding thickness to the panel will not close that gap.
  • Clips fix the panel to the bearer, not to the structure. The standard GRP clip system holds the panel down against wind uplift and against movement; it does not transfer the deck load into the frame. That is the bearer's job.
  • Thermal movement is a bearer detail. GRP expands and contracts roughly two to three times as much as steel over the same temperature range. Every few metres the fixing detail has to allow for it, or the deck will find its own relief by cracking a connection.
  • Order them together. Panels, bearers and clips on one shipment is cheaper and far simpler than three shipments on three dates. It is also the usual reason a deck sits half-built waiting for a profile that was ordered separately.

A note on mixed materials: bolting GRP profiles to steel is common and workable, but the connection needs an isolating detail, because the composite is not electrically conductive in the way the steel frame is and the two behave differently under load and under thermal movement. Detail it at design stage rather than discovering it on site.

Performance

Load, Span and Deflection in Practice

Deflection is the governing criterion for almost every GRP structural member, and the limit normally applied is span over 200 for a walkway or a platform where people work, or span over 100 where a tighter feel is wanted. The table below sets out the relationship that drives the section choice, so that a specification can be read against it.

SpanWhere a channel stops being comfortableWhere an I-beam is neededWhat usually governs
Up to 1.5 mA modest channel is adequate for a light walkway loadNot normally requiredStrength, not deflection
1.5 to 3 mDepth has to rise quickly; a channel becomes inefficientI-beam takes over as the efficient choiceDeflection at span/200
3 to 5 mNot practical for a single channel spanDeeper I-beam, and often a two-member or braced arrangementDeflection, and the stiffness the grade provides
Beyond 5 m—Requires an engineered arrangement rather than a stock profileDeflection and the connection design together

The ranges above are indicative and are not a substitute for a calculation on the actual load case. What they establish is the shape of the problem: as span grows, deflection rises with the cube of the span, so doubling the span multiplies deflection by roughly eight for the same section. That is why a bearer that works at 1.8 m fails at 3.6 m, and why adding thickness to the panel instead of depth to the bearer never solves it.

Resin

Resin Systems and the Exposure They Answer

The profile's resin system decides what the member survives, and it is chosen for the environment rather than for the price. Getting this wrong is the most expensive mistake available on a composite structure, because a resin that is wrong for the exposure cannot be corrected by adding thickness.

Isophthalic Polyester

The general-purpose structural choice. Adequate for inland industrial atmospheres, fresh water and moderate chemical exposure, and the most economical route where the environment is genuinely benign.

Orthophthalic Polyester

The lowest-cost system, and the one to be suspicious of on an outdoor or coastal structure. It is fine indoors in a dry atmosphere and inappropriate where salt, UV or chemical splash is present.

Vinyl Ester

The standard answer for coastal, marine, offshore and chemical service. Better resistance to chloride, to acids and to hydrolysis, and the system specified when the structure is expected to last decades under attack.

Phenolic

Chosen for fire performance and low smoke rather than for chemical resistance. Where a fire strategy demands a limited-combustibility member, phenolic is the route, at a higher cost and with a different surface finish.

A note on UV: GRP profiles are protected against sunlight by a surface veil and by a UV inhibitor in the resin, not by being inherently immune. A profile with a good veil will hold its appearance and its properties outdoors for many years; a cheap profile without one will chalk and expose fibre. On an outdoor UK structure this is a visible, checkable difference.

Comparison

GRP Profiles Against Steel and Aluminium

GRP pultrudedGalvanised steelAluminium
Corrosion in coastal or chemical serviceUnaffected by chloride; the reason it is specified at allGalvanising is a coating with a finite life; the section corrodes once it is breachedResistant to atmosphere, but attacked by chloride and by alkalis
WeightRoughly a quarter of steel for the same sectionThe reference weightRoughly a third of steel
StiffnessLower modulus, so deflection governs the sectionHigh modulus; the efficient choice where stiffness is the limitModulus between the two
Electrical conductivityNon-conductive; relevant near electrical equipmentConductiveConductive
Thermal movementTwo to three times steel; needs a movement detailThe referenceHigher than steel, lower than GRP
Site modificationCut and drilled with normal tools, dust needs controlCut and weldedCut and welded or bolted
Best fitCorrosive exposure, electrical proximity, weight-sensitive access, and structures that must not be re-paintedLong spans where stiffness governs, and hot or fire-critical structureWeight-sensitive structures in a benign atmosphere

The honest summary is that GRP wins on corrosion and on weight, and loses on stiffness. A specification that asks a GRP profile to do a steel beam's job over a steel beam's span will end up with a deep, heavy-looking member or an unacceptable deflection. Where the structure must be stiff over a long span, steel is the right material and saying so is more useful than selling a composite into a load case it cannot serve.

Fabrication

Cutting, Drilling and Connecting on Site

GRP profiles are fabricated with ordinary tools, which is one of their real advantages, but the details matter more than they would on steel because the material is anisotropic — strong along the fibre, much weaker across it.

  • Cutting. A fine-tooth carbide blade or a diamond blade, with dust extraction. The dust is an irritant and a nuisance, and a wet cut or extraction keeps the site clean and the operatives comfortable.
  • Drilling. Standard HSS or carbide bits, with a backing plate to prevent delamination at the exit. Drilling close to an edge is the common failure — keep the hole at least one and a half diameters from the edge.
  • Bolting. Through-bolts with washers on both sides, and a clearance hole rather than a tight fit, because the material needs room to move. Over-tightening crushes the section locally and is invisible until it fails.
  • Sealing cut edges. A cut exposes fibre, which is the one place a GRP profile can start to wick moisture. On an outdoor or wet-service structure, seal the cut face with a compatible resin or a proprietary edge sealant.
  • No welding. There is no site weld for a GRP profile. Connections are bolted, bonded or made with a purpose-made fitting, and the detail has to be designed rather than improvised.
Applications

Where GRP Structural Profiles Are Specified

Water and Wastewater Works

Walkway bearers, platform frames and handrail posts over tanks and channels. Vinyl ester throughout, and the reason the site does not need a re-painting programme.

Coastal and Marine Structures

Jetty walkway frames, fender support, access platforms at the waterline. The exposure that galvanised steel loses on and GRP is specified for.

Chemical and Process Plant

Pipe rack support, bunded area frames and access structure in acid or alkali service. Resin selection, not section size, is the design decision here.

Offshore and Wind

Module walkway frames, turbine access structure and platform bearers where weight and corrosion resistance both matter and maintenance access is expensive.

Food and Beverage

Wash-down area frames and mezzanine support where a smooth, cleanable, non-corroding member is required and a painted steel frame would fail an audit.

Electrical and Telecoms

Support structure near live equipment, where a non-conductive member removes a step-change hazard rather than managing it.

Related

Related GRP and GRP/FRP Pages

More GRP guides: GRP grating price · GRP grating clips · GRP walkway grating · GRP trench cover grating · GRP stair tread grating

GRP Grating — Full Range

The complete overview: moulded and pultruded panels, resin systems, standards by market and terminology.

GRP Grating Panels

Panel sizes, thickness, weight and load data — the surface that sits on the bearers specified here.

GRP Grating Manufacturer

How the panel and the profile are made, and what a factory approval pack actually contains.

GRP Grating Supplier

Supply terms, lead times and the documentation pack, with profiles and panels consolidated on one shipment.

FRP Pultruded Profiles

The same member under its North American name, for buyers working to ASTM specifications.

Heavy Duty GRP Grating

50 and 60 mm panels and traffic classes, for the load cases a standard panel cannot carry.

GRP Platform Grating

Everything a platform deck has to answer for: working load, load class, panel thickness and the support arrangement beneath.

GRP Channel Grating

Drainage and duct covers sized to the channel, with the load class, open area and handling weight in one place.

GRP Catwalk

Elevated access walkways for pipe racks, tank farms and modules, supplied as labelled kits for a one-day installation.

GRP Grating Suppliers

Supplier selection without the guesswork: documentation checks, commercial signals and the weight test that reveals glass content.

FAQ

GRP Structural Profiles — Frequently Asked Questions

What is the difference between GRP structural profiles and GRP grating?

The profile is the support member and the grating is the walking surface. A pultruded GRP profile is a solid-section beam, channel or angle that spans metres and carries the deck load; a GRP grating panel is an open-mesh product that sits on top and provides the walking surface. They are bought together because the profile sets the span the panel is allowed to cover.

What standard covers GRP pultruded profiles?

BS EN 13706, which defines grades E17 and E23 by measured mechanical property rather than by description. Ask for the grade stated on the datasheet as E17 or E23 to BS EN 13706. Note that BS EN 13706 covers the profile, not the grating — grating falls under BS 4592, and the two standards are not interchangeable.

Which grade do I need, E17 or E23?

E17 is the standard structural grade and covers most platform bearers, stringers and handrail posts. E23 has a higher modulus and is specified where deflection governs — long spans, tight deflection limits, or heavy load cases. Because GRP is usually stiffness-limited rather than strength-limited, the modulus is the number that decides the section.

How far can a GRP beam span?

Deflection governs, and deflection rises with the cube of the span. A modest channel is comfortable to about 1.5 m, a channel becomes inefficient between 1.5 and 3 m where an I-beam takes over, and beyond 5 m the arrangement needs engineering rather than a stock profile. The figures are indicative and a real load case needs a calculation.

Can GRP profiles replace steel beams?

On corrosion and weight, yes, and that is why they are specified. On stiffness, not always: GRP has a lower modulus, so a GRP member doing a steel beam's job over a steel beam's span will be deep or will deflect unacceptably. Where the structure must be stiff over a long span, steel remains the right material.

Which resin should I specify for a coastal site?

Vinyl ester. It gives materially better resistance to chloride, to acids and to hydrolysis than polyester, and a coastal or marine structure is exactly the exposure where the difference shows over decades rather than months. Orthophthalic polyester is the system to avoid outdoors, whatever the price difference.

Do GRP profiles need painting?

No, and that is one of the commercial arguments for them. The surface is protected by a veil and a UV inhibitor in the resin, so an outdoor profile holds its appearance for many years without a maintenance coating. A cheap profile without a proper veil will chalk and expose fibre, which is a visible difference worth checking on a sample.

How are GRP profiles connected?

Bolted, bonded, or with purpose-made fittings. There is no site weld for a composite profile. Through-bolts need washers on both sides and a clearance hole rather than a tight fit, because the material needs room for thermal movement. Over-tightening crushes the section locally and stays invisible until it fails.

Do I need to seal cut edges?

On any outdoor or wet-service structure, yes. A cut exposes fibre, and an exposed fibre face is the one place moisture can wick into the section. Seal it with a compatible resin or a proprietary edge sealant. On a dry indoor structure the risk is lower, but sealing costs little and removes the concern.

What is the thermal movement and why does it matter?

GRP expands and contracts roughly two to three times as much as steel over the same temperature range. The fixing detail has to allow for it every few metres, or the deck will find its own relief by cracking a connection. It is a detail, not a material problem, but it is the detail most often left out.

Can you supply profiles cut to length?

Yes, cut to a schedule rather than shipped in random lengths for site cutting. Cut-to-length removes the site cutting step, keeps the cut faces consistent, and means the edge sealing can be done under factory conditions rather than in the wind on a platform.

Do profiles and grating ship together?

They can, and they should. Panels, bearers and clips consolidated on one shipment is cheaper and simpler than three shipments on three dates, and it is the usual reason a deck sits half-built waiting for a profile that was ordered separately. Give the bearer schedule and the panel schedule in one enquiry.

Shape pages

One Page per Pultruded Section

Next Step

Request GRP Structural Profile Pricing

Send the profile shapes, the lengths and the span they have to clear. You will get an itemised quotation stating the grade, the resin system and the lead time — and if a different material would serve the load case better, you will be told that instead.

Request Profile Pricing → GRP Grating Calculator

NANTONG ZEALL NEW MATERIALS CO., LTD. · Pultruded GRP profiles to BS EN 13706 · ISO 9001 certified

Definition

GRP Structural Sections for Pultruded Composite Framing

GRP structural sections are the solid, constant-profile members that carry a GRP deck where steel, aluminium or timber would corrode, rot or conduct. Made by pultrusion – glass roving and surfacing veil pulled through resin and a heated die – they run in lengths of metres and are cut, drilled and bolted on site.

They are bought alongside the grating panel: the panel is the walking surface, the GRP structural section is the bearer that sets the span the panel may cover. Specified to BS EN 13706 as grade E17 or E23, with vinyl ester for coastal and chemical duty and isophthalic polyester for general wet service.

Sections & grades

Section Family, Grades and Corrosion Choice

The family covers I-beam and H-beam bearers, channel stringers, angle cleats, square and rectangular tube columns, flat bar bearing plates and solid rod ties. Stiffness governs design more often than strength: a GRP beam deflects long before it breaks, so the declared E17 or E23 modulus – not a generic structural label – is what the engineer checks against a load case.

Names are interchangeable on drawings: GRP, GFRP and fiberglass structural sections all mean pultruded glass-reinforced polymer; pultruded, pultrusion and structural shapes describe the same manufacturing route. Pick the cross-section on the shape-selection page, read the structural sections overview, and arrange supply and tooling on the manufacturer page. The FRP grating supplier desk pairs these bearers with the deck above.

GradeDeclaresTypical role
E17Standard structural grade, declared tensile/flexural/compressive valuesPlatform bearers, handrail posts, general framing
E23Higher modulus from higher glass content and tighter processLong spans and deflection-governed load cases
FAQ

GRP Structural Sections — Frequently Asked Questions

Can you pultrude a non-standard GRP structural section?

Yes. We cut new steel dies in-house for custom channel depths, hat sections, C and Z profiles, ladder rails and integrated fixing feet. Send a drawing or sample and we confirm feasibility, glass content and tooling lead time.

What is the minimum order quantity?

Our minimum starts at 10 m² equivalent. Standard I-beam, channel, angle and tube sections can be quoted in smaller trial quantities.

Which export terms and lead time do you offer?

We ship EXW, FOB Shanghai or CIF to your destination port, sea-worthy crated. Standard lead time is 12–36 working days after order confirmation, depending on resin, tooling and volume. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com