📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
Heavy Duty GRP Grating · Forklift & Truck Loads · High-Load Panels

Heavy Duty GRP Grating

Heavy-Duty GRP Grating · Forklift / Truck Rated · Long-Span Pultruded — high-load glass reinforced plastic grating for vehicle, forklift and point-load industrial zones.

ISO 9001 Certified
Direct FRP Grating Master Factory
Exported to 45+ Countries
ISO 9001
Quality Management
45+ Countries
Global Export Network
20+ Years
Manufacturing Experience
Custom OEM/ODM
Engineering Support

Heavy duty GRP grating carries loads that standard walkway grating is not built for — forklift traffic, pallet trucks, light vehicles and concentrated point loads. FRP Grating Master builds heavy-load glass reinforced plastic grating using deep pultruded profiles and vinyl ester resin, engineered to span between supports without sagging or permanent deflection. It is the flooring of choice for plant access roads, loading bays, truck platforms, waste-treatment traffic areas and offshore module decks.

Overview

Load Classes & Span Guidance

How Load & Span Relate

The safe working load depends on panel thickness, bar profile, bar spacing, support span and a safety factor. Deeper pultruded profiles (38/50 mm) and closer bar spacing carry heavier point loads at longer spans. We calculate the correct panel for your forklift model and support centres.

Typical Span Table (illustrative)

Use the table below as a guide; final selection is confirmed by load calculation. Always verify against site forklift axle loads and support spacing.

Overview

Applications & Specification

Where Heavy-Duty GRP Grating Is Used

Forklift routes on chemical and water-treatment plants, loading bays, truck platforms, waste processing, offshore module decks and vehicle ramps. Anti-slip gritted or concave tops are recommended — see anti-slip FRP grating.

Materials & Supply

Vinyl ester resin for chemical/heavy service, UV-stabilised for outdoor. Explore pultruded grating, platform grating and the full product range; request a load calculation via contact.

Technical Specifications

Heavy-Duty GRP Grating Technical Specifications

Heavy-duty GRP grating is engineered for forklift, pallet and occasional vehicle traffic where pedestrian-grade 25–38 mm panels would deflect. It uses thicker molded panels or pultruded I-bar profiles in polyester or vinyl ester resin. The table below lists the standard heavy-duty range we supply.

Parameter50 mm Molded75 mm Pultruded I-Bar100 mm Pultruded I-Bar
Panel thickness50 mm75 mm100 mm
Bar / mesh spacing38×38 mm40 mm bar centres40×60 mm
Standard panel size1220×3660 mm1220×6000 mm1220×6000 mm
SurfaceGrit-top / CoveredGrit-topGrit-top / Smooth
ResinIso / Vinyl EsterIso / Vinyl EsterIso / Vinyl Ester / Phenolic
Typical usePallet truck lanesForklift trafficTruck / long span
Duty classCDD (heavy industrial)
Load Classes

Real Load Classes and Point-Load Ratings

The table below summarises typical working loads for heavy-duty GRP grating, as used in our load-test data and published guides. Point load is the concentrated load a 1220 mm-wide panel carries over its support span at a safe deflection; uniform load is in kN per square metre. Verify against your own span before specification.

Panel / ThicknessSupport SpanPoint Load (kN)Uniform Load (kN/m²)Typical Traffic
38 mm molded600 mm3.05.0Pedestrian
50 mm molded750 mm5.07.5Pallet truck / cart
50 mm pultruded900 mm7.510.0Light forklift
75 mm I-bar pultruded1200 mm10.015.0Forklift / pallet rack
100 mm I-bar pultruded1500 mm15.020.0Heavy forklift / truck
Resin Selection

Resin Selection for Heavy-Duty Service

Heavy loads and aggressive environments often go together. Choose the resin for the chemicals the floor sees, then the section for the load.

ResinRelative CostChemical ResistanceFire RatingBest For
Isophthalic polyesterBaselineGoodASTM E-84 Class BGeneral industrial platforms
Vinyl ester+15–25%Excellent (acids, alkalis, salt)ASTM E-84 Class BRefineries, coastal, wastewater
Phenolic+20–35%Moderate; low smokeASTM E-84 Class ATunnels, fire-critical heavy zones
Load & Span

Span, Thickness and Traffic Selection

Overspecifying wastes money; underspecifying deflects dangerously. Match the section to both the traffic and the unsupported distance between beams.

Traffic on FloorRecommended PanelMax Unsupported Span
Pedestrian only25–38 mm molded600 mm
Hand pallet truck50 mm molded750 mm
Powered pallet / small forklift50–75 mm pultruded900–1200 mm
Counterbalance forklift / truck75–100 mm I-bar1200–1500 mm

See the heavy-duty load capacity guide for full deflection and safety-factor calculations.

Installation

Installation Guide for Heavy-Duty Grating

  1. Check drawings and confirm bearing support; lay panels on clean, level steel or GRP beams with the recommended bearing width on each support.
  2. Pre-drill fixing holes only where needed; align panels to the grid and leave a 10–15 mm expansion gap between adjacent panels.
  3. Fasten with stainless steel FRP grating clips — minimum 4 clips per 1220×3660 mm panel, one at each corner, plus extra clips for heavy traffic or wind-uplift zones.
  4. Cut panels with a carbide-tipped or diamond blade; wear dust protection and seal cut edges on vinyl ester or phenolic panels when required.
  5. Walk the installed grid to check deflection and clip torque, then clear offcuts and install edge trim or toe-kicks where specified.

For forklift-rated floors, add clips along both long sides (6–8 per panel), use heavier SS316 fixings, and confirm bearing length on steel supports — see the clip range.

Applications

Industry Applications for Heavy-Duty Grating

Forklift and warehouse lanes: pultruded I-bar GRP grating carries repeated pallet-truck and forklift wheel loads where steel would corrode or need repainting around chemical storage.

Refineries and heavy plants: vinyl ester heavy-duty grating resists hydrocarbon and H2S exposure while providing a non-sparking, non-conductive floor for maintenance crews.

Mining, power and truck loading: long-span 75–100 mm panels reduce the number of support beams, and the light weight means faster, safer installation at height.

Heavy Duty

When to Specify Heavy-Duty GRP Grating

Step up from standard molded grating when any of the following is true: (1) forklift or pallet-truck wheel loads, not just foot traffic; (2) unsupported spans beyond 750 mm; (3) corrosive or coastal duty that would rust steel; (4) requirement for a non-conductive, non-sparking floor. In each case the higher upfront cost is recovered through service life and avoided shutdowns. Compare against metal in the FRP vs steel cost comparison.

Related Pages

Related Products and Guides

More GRP guides: GRP grating price · GRP grating clips · GRP walkway grating · GRP trench cover grating · GRP stair tread grating

GRP Platform Grating

Load classes, mesh, thickness and the bearer spacing a platform deck needs, with the working-load figures behind each class.

GRP Channel Grating

Trench, duct and drainage covers from A15 to C250, with open area, resin choice for corrosive runs and cut-to-channel-width supply.

GRP Catwalk

Modular elevated walkway kits: deck, pultruded frames and handrail, installed by hand without a crane or hot work.

GRP Grating Suppliers

Twelve checks for comparing suppliers, from resin system and glass content to certification and a dated lead time.

Get Started

Request Your Heavy Duty GRP Grating Quote

Email sales@gratingfrp.com · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China

Explore GRP Grating by Topic

FAQ

Heavy Duty GRP Grating FAQ

What loads can heavy-duty GRP grating carry?
Heavy-duty GRP grating is engineered for forklift, pallet-truck and light-vehicle traffic. The exact capacity depends on thickness, bar profile, spacing and support span — we confirm it with a load calculation for your equipment.
Which thickness is best for forklift traffic?
For forklift and point loads we typically specify 38 mm or 50 mm deep pultruded profiles in vinyl ester resin, with anti-slip gritted or concave tops.
Do you provide load / span calculations?
Yes. Send your forklift model, axle load and support centres, and we will specify the correct panel and confirm safe working loads.
Is heavy-duty GRP grating corrosion resistant?
Yes. Vinyl ester and isophthalic resin GRP resists chemical and coastal corrosion far better than steel, without the painting and rust maintenance. Ask about our marine and offshore FRP grating.
What is the load capacity of heavy duty GRP grating?
It depends on thickness and span. A 50 mm molded panel carries roughly 5 kN point load over a 750 mm span, while 75 mm and 100 mm pultruded I-bar panels carry 10–15 kN point load over 1200–1500 mm spans. Send your span and wheel load for a rated calculation.
Which heavy-duty grating thickness handles forklift traffic?
Forklift-rated floors normally use 75 mm or 100 mm pultruded I-bar grating, not molded panel. Counterbalance trucks and long spans require the 100 mm section with SS316 clips along all edges.
How far can heavy-duty GRP grating span without support?
A 75 mm pultruded panel typically spans up to about 1200 mm and a 100 mm I-bar up to about 1500 mm at heavy industrial duty. The exact figure depends on the design load and required deflection limit.
Is pultruded grating better than molded for heavy loads?
For long spans and forklift traffic, pultruded I-bar profiles are stronger per kilogram because continuous rovings run along the load direction. Molded grating is more economical for pedestrian and pallet-truck duty.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com