📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
ZeAllgrate Engineering Resources

Grating Specifications

Individual specification pages for each standard mesh and grating type.

Individual specification pages for each standard mesh and grating type.

Specification pages by mesh and grating type

molded-38x38molded-25x100molded-50x50molded-19x19-minipultruded-38x38pultruded-25x100pultruded-heavy-ibar

Pultruded grating by bearing bar depth and opening

Every pultruded section we pultrude, listed by depth so a specifier can compare load, weight and open area side by side. Each page carries a technical table, an indicative load table and the fixing detail for that section.

25 mm T-bar pultrudedLight 25 mm T-section, 40% or 60% open, 7.5-9.5 kg/m238 mm T-bar pultrudedThe workhorse section, 11.5-13 kg/m2, spans to 3 m50 mm T-bar pultrudedDeep T-section for 3-4 m spans, 15-17 kg/m225 mm I-bar pultrudedTwin-flange I-section at 25 mm, twist resistant38 mm I-bar pultrudedFull platform capability, 12.5-14.5 kg/m250 mm I-bar pultruded3.5-4 m spans, 16.5-19 kg/m276 mm I-bar pultrudedDeepest standard section, 4.5 m spans, 23-26 kg/m218% open area pultrudedDense layout, about 5 mm clear, drop-through and hygiene60% open area pultrudedMaximum drainage and airflow, 7.5-12.5 kg/m2ADA compliant 38 mm pultrudedOpenings within the 13 mm accessible walking-surface limitHeavy-duty I-bar pultrudedHigh-load I-section for plant and trolley traffic38x38 pultruded gratingStandard 38 mm pultruded bar at 38 mm pitch25x100 pultruded gratingHigh open area rectangular layout

Molded grating by mesh size

Molded panels are defined by their mesh rather than their bar depth, because the mesh decides heel safety, drainage and what can fall through the deck.

38x38 molded gratingThe standard 1.5 in square mesh molded panel19x19 mini-mesh moldedFine mesh for heel safety and small parts30 mm 20x20 mini-mesh20 x 20 mm opening at 30 mm depth, about 10 kg/m238 mm 25x152 superspanRectangular mesh, directional capacity, 65-70% open25x100 molded gratingRectangular 1 x 4 in mesh molded panel50x50 molded grating2 in square mesh for heavy foot traffic

Grating fixings and clips

The clip is the part that decides whether a deck stays flat. Each fixing type has its own page with bolt size, quantity per square metre and installation steps.

M-clipStandard saddle fixing, no drilling, 8-12 per m2C-clipEnd panel fixing at the bearer flangeL-clipCorner, post base and upstand fixingW-clipWide-bearing washer clip for thin flanges and gritT-clipPanel joint fixing over a shared bearerSaddle clipHeavy-duty U-form clamp for deep bars and uplift

Verification documents for these sections are collected in certifications and third-party verification, with testing detail in laboratory and test capability; datasheets and reports are issued through downloads and document pack.

Before you fix a section, three calculators use the tables on these pages: span and load for the allowable uniform load at your clear span, weight for panel and order mass, and panel layout for panel count and offcut.

Not sure which section fits? Send the span, the load and the environment through the contact form and we will return a section and a fixing layout for the deck.

Selection data behind every specification page

Each page in this section documents one standard mesh or pultruded profile with the data that decides a specification: mesh opening, panel size, thickness, open area, resin system, surface option and fixing. Published values describe the standard product. Where a project needs another mesh, a longer panel or a different resin, the factory quotes a custom build rather than changing the standard.

Ordering facts that apply to every page here

  • Standard panel 1220 × 3660 mm; pultruded grating up to 1220 × 6096 mm, cut to size
  • Thickness range 25, 30, 38, 50 and 65 mm depending on the product family
  • Resin systems: orthophthalic, isophthalic, vinyl ester and polyurethane
  • Surface options: smooth, gritted, and anti-slip gritted
  • Barcol hardness ≥ 40; density 1.5–2.0 g/cm³
  • Minimum production order 10 m²; lead time 12–36 working days

Use the load and span data on the individual pages to size bearers before ordering; the factory confirms deflection limits against the project drawing.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com