FRP Stair Tread
FRP Stair Tread Grating · Anti-Slip Nosing · Custom Widths — corrosion-proof fiberglass stair treads with gritted nosings for safe industrial and coastal stairs.
FRP stair tread grating turns ordinary steel or composite stairways into safe, corrosion-proof access. FRP Grating Master manufactures fiberglass stair treads with anti-slip gritted nosings that resist wet, oily and coastal conditions. Lightweight and non-conductive, they suit industrial stair towers, offshore modules, water-treatment plant, coastal structures and rooftop egress where steel treads would rust or conduct.
Stair Tread Features
Anti-Slip Nosing
The leading edge of each tread carries a gritted anti-slip nosing for grip and edge visibility — critical for wet-shoe, chemical-wet and night-time egress.
Custom Widths & Loads
Treads are made to your stair width and depth, in 25/30/38/50 mm thickness, polyester or vinyl ester resin. Heavier pultruded profiles suit high-traffic or vehicle-access stairs.
Applications & Supply
Where Used
Industrial stair towers, offshore modules, wastewater and pumping stations, coastal and marine structures, solar and rooftop egress. Pair with walkway grating and platform grating.
Ordering
Send stair width, depth and quantity (and a drawing if available). Browse products, custom sizes and request a quote via contact.
FRP Stair Tread Grating Technical Specifications & Sizes
FRP stair tread grating is supplied as cut-to-size treads built on molded or pultruded FRP grating with a gritted anti-slip nosing. The table below lists the standard parameters we manufacture to, so you can match your stair width, depth and traffic class before requesting a quote.
| Parameter | Standard Range | Notes |
|---|---|---|
| Tread thickness | 25 / 30 / 38 / 50 mm | 38 mm is the common industrial choice |
| Tread width (going) | 300 – 400 mm | Made to your stair width |
| Tread length (width of stair) | 300 – 1500 mm | Cut to stair width + nosing overhang |
| Mesh / bar spacing | 38×38 / 19×19 mm | 19×19 for fine-footwear safety |
| Nosing | Grit anti-slip, yellow or grey | Edge visibility + grip |
| Resin system | Isophthalic / Vinyl ester | Phenolic on request for fire zones |
| Typical load class | A – C (pedestrian to light vehicle) | Per-step deflection controlled |
Every tread is cut to your drawing with bolt holes and end caps, and supplied with COA and load test reports.
FRP vs Steel vs Aluminium Stair Treads
For stair treads exposed to water, chemicals or coastal air, material choice drives both safety and life-cycle cost. The table compares the three common tread materials on the properties that matter most on a stair.
| Property | FRP Stair Tread | Steel (HDG) Tread | Aluminium Tread |
|---|---|---|---|
| Corrosion | Immune to rust | Rusts if coating damaged | Corrodes in salt/alkali |
| Weight | Light (~1/4 of steel) | Heavy | Light but softer |
| Slip resistance | Grit nosing, works wet | Slippery when wet/oily | Slippery when wet |
| Electrical / thermal | Non-conductive | Conductive | Conductive |
| Service life (corrosive) | 20+ years | 5–8 years recoat cycle | 10–15 years |
See our FRP vs steel grating cost comparison for the full lifecycle argument.
Resin Selection for Stair Treads
Pick the cheapest resin that still meets your environment. Stairs in general plant areas use isophthalic polyester; wet chemical or coastal stairs step up to vinyl ester; fire-critical escape stairs use phenolic.
| Resin | Relative Cost | Chemical Resistance | Fire Rating | Best For |
|---|---|---|---|---|
| Isophthalic polyester | Baseline | Good | ASTM E-84 Class B | General walkways and platforms |
| Vinyl ester | +15–25% | Excellent (acids, alkalis, H2S) | ASTM E-84 Class B | Chemical, marine, wastewater |
| Phenolic | +20–35% | Moderate | ASTM E-84 Class A (low smoke) | Tunnels, rail, fire-critical zones |
Send your chemical list with the RFQ and we will specify the most economical compliant system — see the vinyl ester vs polyester resin guide.
Tread Load and Thickness Selection
Stair treads carry people (and occasionally hand-tools or carts) across a short span between stringers. Match thickness to going and traffic to avoid under- or over-engineering.
| Application | Recommended Tread | Max Going (span) |
|---|---|---|
| General pedestrian stair | 25–30 mm molded + grit nosing | 300 mm |
| Industrial high-traffic stair | 38 mm molded / pultruded | 350 mm |
| Coastal / chemical stair | 38 mm vinyl ester | 350 mm |
| Tool-cart / light access stair | 50 mm pultruded | 400 mm |
Send your going, width and traffic class and our engineers confirm deflection before quoting.
Stair Tread Installation Guide
- Measure the going and width of each step; order treads to finished size with the nosing overhanging the leading edge.
- Fix treads to steel or concrete stringers with stainless steel (SS316) bolts or FRP clips — two fixings per tread minimum.
- Seal cut edges on vinyl ester treads if trimmed on site; deburr drilled holes.
- Align the anti-slip nosing consistently on the leading edge for visual and grip safety.
- Check every tread is flush and free of movement before handing over; re-torque after the first weeks of use.
Follow the step-by-step installation guide and use stainless grating clips.
Where FRP Stair Tread Grating Is Used
Industrial stair towers: grit-nosed FRP treads stay safe in wet, oily weather and never rust, eliminating the steel tower maintenance cycle.
Offshore modules and coastal structures: non-conductive, salt-proof treads avoid electrolysis and are light enough for manual handling during retrofit. See marine FRP grating.
Wastewater and pumping stations: vinyl ester treads resist H2S and acid mists where steel stairs would corrode within a few years — see wastewater plant guidance.
Anti-Slip Nosings and Custom Stair Profiles
Beyond standard rectangular treads we fabricate wedge, arc and winder treads, bolt-down or weld-plate fixing, and colour-coded nosings (yellow safety edge). Treads pair naturally with FRP walkway grating and platform grating for a complete corrosion-proof stair-to-platform system. Request custom sizes via custom FRP grating.
Related Products and Guides
- FRP Molded Grating — one-piece panels used as tread blanks
- FRP Pultruded Grating — deep-section treads for long goings
- FRP Grating Clips — SS316 fixings for tread-down
- Anti-Slip FRP Grating — grit and concave surface options
- Anti-Slip Surface Safety Guide
- FRP Grating Glossary — industry terms
Request Your FRP Stair Tread Grating Quote
Email sales@gratingfrp.com · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China
FRP Stair Tread FAQ
Dimensions and Inclines for Pultruded FRP Stair Tread Layouts
Tread Depth, Riser Height and Stair Angle
A standard pultruded FRP stair tread is cut from a 1220 × 3660 mm grating panel to match stair widths up to about 1200 mm. Comfortable industrial stairs use a tread depth of 240–300 mm with a riser of 150–190 mm, which keeps the stair angle in the usual 30–40° working range. The walking face is gritted or fitted with a carborundum nosing rated R13, so the leading edge stays safe even when condensate, rain or oil wets the tread.
Because the profile is pultruded rather than moulded, the tread carries a straight, consistent bar that lines up neatly with the matching FRP walkway grating on the landing and with FRP platform grating at the top of the run. Deflection under the design live load is held to L/200, and open-riser construction keeps rain, snow and debris from pooling on the stair.
Salt Spray and Outdoor Aging Behaviour
UV-stabilised polyester or vinylester resin gives the pultruded FRP stair tread long outdoor life: it does not rust, does not bleed corrosion stains onto cladding and holds its colour in coastal and industrial atmospheres. In salt-spray and wastewater duty, 316 stainless hardware is used, and the tread can be specified in vinylester where acids or solvents are present. Since 2004 our 20,000 m² floor and 200+ staff have supplied these treads to 40+ export countries, with MOQ from 10 m² and lead times of 12–36 working days.
Fixing a Pultruded FRP Stair Tread: Clips, Bolts and Stringers
FRP Stair Tread Fixing Clip on the Stringer
Each pultruded FRP stair tread bears on FRP or steel stringers with a minimum 40 mm bearing length, and it is locked down with two to four FRP stair tread fixing clip fittings plus 316 stainless bolts. The clip hooks under the bearing-bar flange and sits flat against the stringer, so it does not protrude into the walking line and does not need hot-work welding on site. Vibration from traffic or nearby machinery is carried by the clamped joint rather than by a drilled hole in the bar.
Because no welding, grinding or hot work is allowed on many process sites, the clip-and-bolt fixing is a practical advantage: a damaged tread can be unclipped and replaced in minutes while the stair stays in service. Stringers, brackets and posts can be matched from the FRP structural profiles range, and the full fixing set is listed under FRP clips and hardware.
