FRP Platform Grating
FRP Platform Grating · Lightweight · Anti-Slip · Corrosion-Proof — fiberglass platform flooring for industrial, offshore and rooftop working platforms.
FRP platform grating builds safe, durable working platforms where steel would corrode or conduct. FRP Grating Master supplies lightweight fiberglass platform panels that are easy to erect, non-conductive and corrosion-proof, with anti-slip surfaces for safe footing. They are used on industrial access platforms, offshore modules, water-treatment structures, solar and rooftop platforms, and chemical plant walkover decks.
Platform Applications
Industrial & Offshore Platforms
Corrosion-proof platform flooring for chemical plants, offshore modules and water-treatment structures, eliminating the rust and repainting of steel platforms.
Rooftop, Solar & Walkovers
Lightweight platforms on rooftop decks, solar-farm mounting structures and equipment walkovers — easy to handle and install without heavy lifting.
Fiberglass Platform Grating
Fiberglass platform grating is the material-specific name for our corrosion-proof platform flooring, moulded or pultruded to span the platform grid.
Specifications & Supply
Materials & Loads
Molded or pultruded panels in 25/30/38/50 mm thickness; polyester, isophthalic or vinyl ester resin; gritted/concave anti-slip tops. Heavy point-load zones use heavy-duty GRP grating.
Complete Platform Package
Combine platform grating with walkway grating, stair treads and trench covers. Browse products; quote via contact.
FRP Platform Grating Technical Specifications & Sizes
FRP platform grating is engineered to span a structural grid and carry personnel, equipment and light vehicles without corrosion. The table below lists the standard molded and pultruded platform panels we supply, so you can match your platform drawing, support span and load to the right section before requesting a quote.
| Parameter | Molded FRP Platform Panel | Pultruded FRP Platform Panel |
|---|---|---|
| Panel thickness | 25 / 30 / 38 / 50 mm | 38 / 50 / 75 / 100 mm |
| Mesh / bar spacing | 38×38 / 19×19 mm | 40 / 50 mm bar spacing (I-bar, T-bar) |
| Standard panel size | 1220×3660 mm | 1220×6000 mm |
| Surface options | Grit-top / Concave / Smooth / Covered | Grit-top / Smooth |
| Resin system | Isophthalic / Vinyl Ester / Phenolic | Isophthalic / Vinyl Ester / Phenolic |
| Typical platform duty | Pedestrian to light vehicle | Heavy industrial, long-span decks |
Every panel is cut to your drawing with shaped cut-outs, bolt holes and stair-nose options, and supplied with COA, MSDS and load-test reports. Custom mesh, thickness and colour are available on request.
Platform Load and Support Span Selection
The span between supports is what determines the panel depth for an FRP platform. A 25–30 mm molded panel is the most economical choice for pedestrian access, while forklift zones and long offshore spans step up to pultruded sections. Use this quick selection table to size your fiberglass platform grating before engineering approval.
| Platform Duty | Recommended Panel | Typical Support Span | Deflection Note |
|---|---|---|---|
| Pedestrian access walkway | 25 – 30 mm molded | 450 – 600 mm | Deflection ≤ L/200 |
| General industrial platform | 38 mm molded | 600 – 750 mm | Deflection ≤ L/200 |
| Pallet truck / light vehicle | 50 mm molded | 750 – 900 mm | Point-load checked |
| Forklift / equipment deck | 50 – 75 mm pultruded | 900 – 1200 mm | Heavy-duty section |
| Long-span offshore / rooftop | 75 – 100 mm pultruded I-bar | 1200 – 1500 mm | Uplift & point-load rated |
Send your span, load and support layout and our engineers will confirm deflection and load class before quoting. For demanding decks see heavy-duty GRP grating and the load capacity guide.
Resin Systems for Corrosion-Proof Platforms
The resin system decides how long a platform lasts in chemical, wastewater or offshore service. Choose the lowest-cost resin that still meets your environment — never overspend, and never underspecify a working platform.
| Resin | Relative Cost | Chemical Resistance | Fire Rating | Best For |
|---|---|---|---|---|
| Isophthalic polyester | Baseline | Good | ASTM E-84 Class B | General walkways and dry platforms |
| Vinyl ester | +15–25% | Excellent (acids, alkalis, H2S) | ASTM E-84 Class B | Chemical, marine, wastewater decks |
| Phenolic | +20–35% | Moderate | ASTM E-84 Class A (low smoke) | Tunnels, rail, fire-critical platforms |
For the full chemistry see vinyl ester vs polyester resin, or send your chemical list with the RFQ — we will recommend the most economical compliant system.
Platform Point Loads and Wheel Load Ratings
A platform is only as safe as its worst load case. Fixed equipment, pump bases and pallet-truck wheels concentrate load far above uniform foot traffic, so the table below matches common platform zones to a panel section — over-specifying wastes money, under-specifying risks deflection and fatigue.
| Platform Zone | Typical Load Case | Recommended Section | Profile |
|---|---|---|---|
| Personnel walkway | 5 kN/m² uniform | 25–30 mm molded | Mesh grid |
| Plant floor access | 10 kN point load | 38 mm molded | Mesh grid |
| Pallet / pump base | 20 kN wheel load | 50 mm molded | Heavy mesh |
| Forklift traffic deck | 25 kN axle load | 50–75 mm pultruded | I-bar / T-bar |
| Offshore equipment skid | 40 kN concentrated | 75–100 mm pultruded | Deep I-bar |
Point loads are checked against the actual support layout, not just panel depth. We supply load-test certificates for any zone where forklift or static equipment loads apply.
Platform Installation and Fixing Guide
- Set out the steel or FRP support structure to the drawing; lay panels on clean, level beams with the recommended bearing width on each support.
- Secure every panel with stainless steel FRP grating clips — minimum four clips per 1220×3660 mm panel, one at each corner.
- On wind-exposed or offshore platforms, add clips along the long sides (six or more per panel) to resist uplift.
- Cut panels with a carbide-tipped blade; seal cut edges on vinyl ester or phenolic panels where required.
- Allow a 10–15 mm expansion gap between panels and integrate FRP handrail systems at open edges and stair openings.
See the step-by-step installation guide and pair platforms with walkway grating for a complete access solution.
Industry Applications for FRP Platform Grating
Offshore and oil & gas modules: non-conductive, salt-water resistant fiberglass platform flooring eliminates electrolysis between deck and steel structure and needs no repainting. Pultruded I-bar panels handle the long unsupported spans common on offshore decks — see marine FRP grating and offshore application notes.
Wastewater treatment: 38 mm vinyl ester molded panels are the standard floor for aeration galleries and tank-top platforms — no rust staining, no shutdown for coating, and a 20+ year service life in H2S service. See wastewater treatment plant applications.
Rooftop and solar platforms: the light weight of FRP platform grating means decks can be installed on roofs and solar mounting structures without heavy lifting, while the anti-slip gritted surface keeps maintenance crews safe in wet conditions.
Custom Platform Design and Long-Span Decks
When a standard 1220×3660 mm panel will not fit — around pipe racks, vessel skirts, stair openings or long equipment spans — we cut and fabricate custom platform sections to your drawing. Long-span decks use pultruded I-bar or built-up profiles in place of molded panels, and we can supply the complete package of platform grating, walkway, stair treads, trench covers and handrails in one shipment. See custom FRP grating and anti-slip FRP grating for gritted working surfaces.
Related Products and Guides
- FRP Molded Grating — economical one-piece panels for pedestrian platforms
- FRP Pultruded Grating — I-bar profiles for long spans and forklift decks
- FRP Grating Clips — M, C, L and Z fasteners in SS304 / SS316
- FRP Walkway Grating — access walkways paired with platform decks
- Heavy-Duty GRP Grating — forklift and long-span load classes
- Load Capacity Guide — span and deflection selection
Request Your FRP Platform Grating Quote
Email sales@gratingfrp.com · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China
FRP Platform Grating FAQ
Load Ratings and Support Spacing for Fiberglass Platform Grating
Pultruded FRP Platform Grating Versus Steel Platform Panels
A standard fiberglass platform grating panel measures 1220 × 3660 mm, and the 38 mm deep pultruded profile weighs about 87 kg per panel against a much heavier steel equivalent. Under the L/200 deflection limit used for industrial working surfaces, the p50 section carries 48 kN/m² over a 1.0 m span, 26 kN/m² over 1.25 m and 14 kN/m² over 1.5 m; the p65 section reaches 62 / 35 / 20 kN/m² at the same three spans. This lets engineers size a pultruded FRP platform grating directly on live-load drawings without over-specifying steel.
Compared with a hot-rolled steel platform, FRP panels need no grit-blasting, no hot-dip galvanising and no periodic repainting, and they stay non-conductive around substations and chemical lines. Our 20,000 m² production floor and 200+ trained staff have shipped these panels to 40+ export countries since 2004, with MOQ from 10 m² and lead times of 12–36 working days, certified to ISO 9001 (01708Q11888R0S) and ASTM F3059 (211122012SHF-001).
Support Beam Spacing and Bearing Length
Fiberglass platform grating is carried on pultruded FRP I-beams, C-channels or steel edge beams set at the centres shown on the load tables. Each panel must bear on at least two supports, with a minimum bearing length of 50 mm on the supporting flange; mid-span support should be added wherever the calculated deflection would exceed L/200 under the design live load. Openings around pipework and equipment are trimmed and edge-beamed rather than cantilevered over unsupported spans.
For the support frame itself, engineers usually specify FRP structural profiles so that beams, posts and grating share the same corrosion behaviour. Where the platform feeds an elevated circulation route, it connects naturally to FRP walkway grating and to FRP stair tread grating at every change of level.
Fixing a Fiberglass Platform Grating: Clips, Corners and Edge Detail
Fiberglass Platform Grating Fixing Clip Layout
Each standard 1220 × 3660 mm panel is secured with four to six fiberglass platform grating fixing clips: one at each corner and one or two along the mid-span of the long edges, depending on beam spacing and vibration. Clips are moulded in glass-filled polyamide or in 316 stainless for coastal and wastewater duty, and they hook under the bearing-bar flange without drilling through the walking surface. Because the clip clamps on rather than welds, installation is cold-work, and replacement of a damaged panel takes minutes without cutting neighbouring panels.
Galvanic reaction is avoided by pairing stainless clips with stainless supports or by using composite clips on FRP support frames; 316 hardware is specified for salt-air and immersion exposure. A full range of matching FRP clips and fixing hardware is stocked alongside the panels, and customers who need a corrosion-aware sourcing partner are directed to our FRP grating supplier page for MOQ, lead-time and certification documents.
