FRP Grating for UK Bottling, CIP and Chiller Roof Walkways

Project Case Studies
Direct Answer

For UK food and beverage plants we specify isophthalic FRP grating on bottling-line crossovers, CIP washdown platforms and chiller roof walkways. The panels stand up to caustic and acid cleaning cycles, stay non-slip when wet, carry 12 kN/m2 at 900 mm, and clip down with SS316 fasteners so maintenance crews never need a hot-work permit on a live production line.

  • Best for: Bottling crossover, CIP platform, chiller roof walkway
  • Specify when: Isophthalic polyester, 38 mm molded, concave surface
  • Key spec: 38 mm isophthalic, 19.5 kg/m2, 12 kN/m2 at 900 mm, SS316

A UK beverage bottler in the Midlands had been replacing steel grating on three routes every four years. Caustic CIP solution, acidic rinse water and wet floor washdowns all attacked the zinc coating from the underside. We supplied 38 mm molded isophthalic panels with concave surfaces, cut to the existing support spacing and fixed with SS316 clips. Three years on, none of the three areas has been blasted, recoated or re-clipped, and the QA audit no longer flags rust bleed on the walkways during BRC reviews.

Site conditions and the three project cases

Why steel fails in a UK food and beverage plant

Painted steel grating in a UK food plant rarely lasts beyond four to five years. Caustic CIP solution at 80 C drips onto the underside of the crossover every wash cycle, and acidic rinse water follows 20 minutes later. Wet floor washdowns leave standing water on the deck, and mild steel clip holes bleed rust into the product area. By year four the panels flex, the welds crack and QA flags the rust streaks during the next BRC audit. The caustic-plus-acid-plus-wet combination is what pushes steel out of food floors.

Case 1: crossover over the bottling line

The bottling-line crossover carries operators across a 12-meter fill line twice per shift, and the deck gets splashed with syrup, beer and rinse water. Painted steel here rusted through at the bar ends in under four years. We installed 38 mm molded isophthalic panels with a concave surface, spanning 900 mm between the existing steel supports and clipped with SS316 fasteners. The concave face sheds rinse water quickly, and the open mesh lets drips fall into the trench below. QA walkthroughs no longer flag rust bleed on the crossover, which used to be a recurring audit finding.

Case 2: platform in the CIP washdown area

The CIP washdown platform sits around the tank and pump skid where operators hoses the system at 80 C with caustic then acid. Steel here was blasted and recoated every two years, but the recoat work required a full line stop. We supplied 38 mm molded isophthalic panels with a smooth top, pre-cut around the CIP return hose and the flow meter. The smooth face wipes clean with a single pass of the pressure washer, and the panels weigh about a quarter of steel at equal stiffness. Line crews now wash the platform during the CIP cycle itself, instead of booking a separate cleaning shift.

Case 3: roof walkway to the chiller units

The chiller roof walkway runs 40 meters across the plant roof to the condensing units, exposed to UK rain, frost and occasional de-icing salt in winter. Painted steel here corroded at the support points in under five years. We laid 38 mm molded isophthalic panels with a grit top, clipped to aluminum stringers with SS316 fasteners. The grit stays non-slip when the roof is wet or frosty, and the UV-stabilized resin keeps the deck from fading. Maintenance crews now service the chillers in winter without the slip risk that came with the wet steel panels.

Product selection, maintenance and specifications

Product types and resin selection

Isophthalic polyester was the right resin here because the media are caustic and acid rinse at moderate temperature, not strong solvents or concentrated acids. Isophthalic handles food-grade cleaning cycles well and stays cost-competitive. For longer roof spans we would have moved to 50 mm pultruded T-bar, which weighs 15 to 17 kg/m2 and clears wider gaps. Surfaces follow duty: concave for the bottling crossover, smooth for the CIP platform, grit for the chiller roof. Every clip is SS316, never carbon steel, so the fasteners do not bleed rust onto a food-grade floor.

Maintenance and service life

Maintenance on these decks is light. During each CIP cycle the crews hose the platform with the same warm water they use on the equipment, and once a quarter the hygiene team scrubs the grit top with a mild detergent. Once a year the engineer walks the route to check clip torque and look for sealed edges. We expect a 15 to 20 year service life in this wet and caustic mix, against four to five years for painted steel. Spare panels are pre-cut to the same dimensions, so a damaged section swaps in with hand tools during a scheduled line stop. No blasting, no recoating, no hot-work permit is needed to keep the walkway in service.

How to start your project

To quote a UK food project we need three inputs. First, a sketch with support spacing, line height and the width of the crossover or platform. Second, the cleaning chemicals the deck will contact directly, including caustic concentration, acid rinse and water temperature. Third, the surface preference and any trolley or hand-truck loading. We come back with a load-table check against the m38 rating of 12 kN/m2 at 900 mm, a resin recommendation, and surface swatches for the hygiene team to test. Our Nantong plant has exported to 45 plus countries for 20 plus years. Send the CIP chemical list and the support spacing first; the surface and clip choice follows from those two.

Standard specifications and delivery

Standard molded panels ship at 1220 by 3660 mm and we cut them to net size at the factory, so the on-site crew only does light fitting around pumps and hoses. Thickness options cover 25, 30, 38, 50 and 65 mm, with the 65 mm panel at 38 kg/m2 for heavy zones. The minimum order is 10 m2, and lead time runs 12 to 36 working days depending on resin and thickness. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. Each shipment carries the ISO 9001 certificate numbered 01708Q11888R0S and the ASTM F3059 report numbered 211122012SHF-001, with SGS inspection on request. Panels are bundled by line and labeled by station so the installer can stage them on the shop floor without a crane.

Key takeaways

Three points sum up this UK bottling job. First, the painted-steel replacement cycle of four years is gone; the isophthalic panels are now in year three with zero recoating. Second, the 38 mm concave panels clear the 900 mm span at 12 kN/m2, which is the rating most bottling crossovers and CIP platforms need. Third, SS316 clips and factory-sealed edges remove the rust-bleed points that used to fail the BRC audit. If you are rebuilding a bottling crossover or a CIP platform, start with the CIP chemical list and the support spacing, and the rest follows.For the technical background see BS-compliant FRP grating shipped to every UK port and Compare concave, grit and smooth FRP surfaces.
Does FRP grating survive caustic CIP washdown?
Yes. Isophthalic polyester handles repeated caustic and acid rinse cycles at food-grade temperatures; we design for 15 to 20 years against 4 to 5 years for painted steel.
Can a panel be swapped without stopping the bottling line?
Panels clip on with SS316 fasteners and need no welding, so one section lifts out during a scheduled line stop without a hot-work permit.
What lead time applies to a food-grade order?
Standard isophthalic 38 mm panels ship in 12 to 36 working days depending on thickness, with a minimum order of 10 m2 and ISO 9001 certificate 01708Q11888R0S attached.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026|Category: Project Case Studies|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating Marine Offshore Projects
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Project background

This case covers an FRP grating supply for a beverage bottling plant in the Midlands in the United Kingdom. The site operated three high-traffic routes that the original painted or galvanized steel could no longer hold up to: crossover over the bottling line, platform in the CIP washdown area, roof walkway to the chiller units.

The operating environment combines caustic CIP solution, acidic rinse water and wet floor washdowns. On the original steel this combination attacked the zinc coating and the bar ends, which is why the client had been replacing the grating every four years and asked for a corrosion-resistant composite alternative that would not need repainting or hot-dip galvanising again.

Grating specification and load design

The panels supplied are 38 mm molded FRP grating in isophthalic polyester with a concave (moulded anti-slip) surface, at a face weight of 19.5 kg/m2. The published key spec for this supply is 12 kN/m2 at a 900 mm simple span, fixed with SS316 clips.

Standard panel size is 1220 x 3660 mm; a 38 mm full panel weighs about 87 kg. For walkways and maintenance platforms the sections are sized as simply supported single spans at L/200 deflection, rated for pedestrian and inspection loading. Heavier pallet or trolley loads are quoted case by case against the molded 38 mm load table (around 25 kN/m2 uniformly distributed at a 600 mm span, 12 kN/m2 at 900 mm, 6.5 kN/m2 at 1200 mm), and pultruded profiles are offered where a longer span is required.

ItemValue supplied
Resin systemisophthalic polyester
Panel thickness38 mm molded
Surfaceconcave (moulded anti-slip) surface
Face weight19.5 kg/m2
Design load (900 mm span)12 kN/m2 (L/200, pedestrian / inspection)
FixingsSS316 clips
Standard panel1220 x 3660 mm (~87 kg)

Installation and site practice

On site the panels are carried by steel or pultruded GRP support beams, with the beam spacing set so the 38 mm panel sits within the 900 mm design span. Panels are seated on neoprene strips and fixed with two SS316 clips per beam per panel, one near each corner; this is the standard practice for walked-on gratings and avoids drilling into the beam flange.

Cutting to field dimensions and holes around nozzles, handrail posts or cable runs are done on site with an abrasive saw or hole cutter, and cut edges are sealed with the matching resin gel to keep the glass fibres encapsulated. Handrails and toe kicks, where required by the layout, are matched pultruded FRP tubes bolted to the panel edge or to a separate steel stanchion; lifting on site is by manual handling because a full panel is light enough for two installers.

  • Support beams: sized to the 900 mm design span, neoprene bearing strips under every panel
  • Fixing: SS316 clips, two per beam per panel, no welding to the structure
  • Cutting and holes: field cutting with abrasive tool, edges re-sealed with resin gel
  • Handrail / toe kick: pultruded FRP tubes, bolted, no metal embedded in the walkway surface

Delivery scope and acceptance points

The page does not publish a quantified outcome such as installed square metres, on-time delivery percentage or a multi-year service-life measurement. The delivery scope that can be verified is the replacement of the three routes named above with 38 mm molded isophthalic polyester panels, fixed with SS316 clips so that no carbon-steel fastener remains in the corrosion zone.

The technical targets the client would normally check at acceptance are: flatness and clip torque on every panel, non-slip performance of the concave (moulded anti-slip) surface surface under wet or oily foot traffic, absence of metal contact in the chloride / solvent / caustic / salt-spray zone, and fit-up around nozzles and rail posts. No customer quote or measured field result is reproduced here because the source page does not disclose one.

Common failure modes in this industry and how to prevent them

1. Clean-in-place (CIP) chemicals (NaOH 2-4%, nitric acid 0.5-1%) attack orthophthalic polyester, turning the surface chalky within 2-3 years.

CIP splashes on walkway joints etch the resin, and food residue then hides in the porous surface, violating HACCP.

Specify vinyl ester or food-grade isophthalic resin for all CIP zones. Ensure all joints are fully sealed; no open-bar edges at walking level.

2. A smooth GRP surface in wash-down areas becomes slippery when wet with water and detergent.

Wet COF drops below 0.4 in wash-down bays. A slip causes falls and possible broken equipment or personnel injury.

Specify a 1.5 mm quartz grit top in all wash-down zones. Maintain 2% drainage slope to floor drains. Add anti-fatigue matting at fixed workstations.

3. Open bar joints trap food particles and biofilm; the gap between bars is wider than the food debris.

Debris in bar gaps harbours Listeria and Salmonella. Cleaning crews cannot reach between bars with a brush.

Specify closed-top or minimesh panels (13x13 mm) in food contact zones. For open mesh, specify bars with rounded edges and schedule quarterly deep cleaning.

4. High-pressure washdown at 80-100 bar aimed at bar joints delaminates the resin-rich layer over time.

Water forced under the surface veil causes blistering and fibre exposure within 3-4 years of daily washdown.

Specify panels with a 0.4 mm C-veil on top. Instruct cleaning crews to keep the wand at 300 mm minimum from the surface. Inspect annually for blistering.

Failure mode Trigger condition Prevention parameters
CIP chemical attack NaOH / nitric acid splash Vinyl ester or food-grade isophthalic; sealed joints
Wash-down slip Water + detergent on smooth GRP 1.5 mm quartz grit; 2% slope; anti-fatigue mats
Food trap in bar gaps Open mesh near food line Closed-top or minimesh 13x13 mm; quarterly deep clean
High-pressure delamination 80-100 bar washdown at joints 0.4 mm C-veil; wand 300 mm min; annual blister check

Related product family and further reading

This case sits inside the molded 38 mm FRP grating family (isophthalic polyester resin, concave (moulded anti-slip) surface), supported by the matching pultruded FRP profiles for frames and handrails, the SS316 clip range, and custom cutting for irregular openings. For longer spans or higher loads the same resin system is also available as pultruded grating and as FRP plate. The links below open the product pages and the adjacent case studies on this site.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com