FRP Grating for Korean Automotive Paint, Welding and Logistics Walkways

Project Case Studies
Direct Answer

For Korean automotive shops we specify molded isophthalic FRP grating on the crossover walkways, welding-cell platforms and outdoor logistics paths that used to be painted steel. The panels hold up against paint-solvent mist, welding spatter and winter road salt, weigh about one quarter of steel at equal load, and clip down with SS316 fasteners so no hot work is needed on the line.

  • Best for: Paint crossover, welding-cell platform, outdoor logistics walkway
  • Specify when: Isophthalic polyester, 38 mm molded, grit top
  • Key spec: 38 mm molded, 19.5 kg/m2, 12 kN/m2 at 900 mm, SS316 clips

A Korean car plant near Ulsan had been replacing painted steel grating on three high-traffic routes every three years. Paint-solvent mist on the paint line, welding spatter in the robot cells and winter de-icing salt on the logistics walkway combined to rust through bar ends and clip holes. We supplied 38 mm molded isophthalic panels with grit tops, cut to the existing support spacing and fixed with SS316 clips. Two years on, none of the three areas has needed repainting, touch-up or clip replacement, and the walkways pass every safety audit.

Site conditions and the three project cases

Why painted steel fails in an automotive plant

Mild-steel bar grating in an automotive shop rarely lasts beyond three to five years. On the paint line, solvent mist drifts onto bar ends every shift and strips the zinc within months. In the welding robot cells, spatter sticks to the top bar and chips off the paint when knocked loose, exposing fresh steel. Outside, winter salt and the occasional washdown from the body shop accelerate under-rust at the clip holes. By year four the panels flex, the welds crack and maintenance crews budget another outage to replace them. That repeat repaint and replace cycle is what pushes steel out of automotive floors.

Case 1: walkway over the paint line

The paint-line crossover is the first spot we rebuilt. Technicians cross over the conveyor twice an hour with paint guns and sample cans, so the deck must stay non-slip even when overspray settles on it. We installed 38 mm molded isophthalic panels with a grit top, spanning 900 mm between existing steel supports and fixed with SS316 clips. The grit sheds overspray better than painted steel, and the open mesh lets drips fall through onto the floor below. Walkway slip events dropped to zero over the first 18 months of service.

Case 2: maintenance platform at the welding robot cell

Inside the welding robot cells the maintenance platform sits one meter above the fixture and carries technicians with toolboxes every shift. Welding spatter rains down at random, so painted steel chips and rusts within a year. We supplied 30 mm molded isophthalic panels with a smooth top, cut to fit around the robot base cables. The smooth face lets spatter flake off instead of embedding, and the panels weigh about a quarter of steel at equal stiffness, so two fitters can lift and swap a panel without a hoist. No hot work was needed to fix the panels, which kept the cell warm-up schedule untouched.

Case 3: outdoor catwalk at the logistics block

The outdoor logistics walkway runs 120 meters between the parts warehouse and the assembly dock, exposed to Korean winter salt and summer humidity. Painted steel here corroded at the support points in under four years. We laid 38 mm molded isophthalic panels with a concave surface, clipped to galvanized stringers with SS316 fasteners. The concave face sheds rain and slush, and the UV-stabilized resin keeps the deck from fading or embrittling. The walkway has gone through two full salt winters with no touch-up painting at all.

Product selection, maintenance and specifications

Product types and resin selection

We chose isophthalic polyester across all three areas because the media here are paint solvents, welding fumes and road salt rather than strong acids or chlorinated solvents. Isophthalic handles UV exposure and mild chemical atmospheres well and stays cost-competitive. For heavier spans we would have moved to 50 mm pultruded T-bar, which weighs 15 to 17 kg/m2 and clears longer gaps; for chemical splash we would specify vinyl ester. Surfaces follow duty: grit top for the paint crossover, smooth for the welding cell, concave for the outdoor path. Clips are always SS316, never carbon steel, to avoid a galvanic bridge under the panels.

Maintenance and service life

Maintenance on these decks is light. Once a quarter the washdown crew hoses the grit top with warm water and mild detergent to lift overspray, and once a year the safety engineer walks the route to check clip torque and look for salt efflorescence at cut edges. Cut edges are sealed at the factory so moisture does not wick into the fibers. We expect a 15 to 20 year service life in this indoor-plus-outdoor mix, against four to eight years for painted steel. Spare panels are pre-cut to the same dimensions, so a damaged section swaps in with hand tools on a shift change. No grinding, no welding, no paint booth is required to keep the walkway in service.

How to start your project

To quote a similar automotive project we need three things from you. First, a simple sketch with the support spacing and the maximum span you want to clear. Second, the process media the deck will see, including solvent names, temperature ranges and washdown chemicals. Third, the surface preference and any wheel or forklift loading. We come back with a load-table check against the m38 rating of 12 kN/m2 at 900 mm, a resin recommendation, and sample swatches of the grit, concave and smooth surfaces for site testing. Our Nantong plant has exported grating to 45 plus countries for 20 plus years. Send the sketch and the media list first; the surface and clip choice follows from those two.

Standard specifications and delivery

Standard molded panels ship at 1220 by 3660 mm, and we cut them to your net size at the factory so the on-site crew only does light fitting. Thickness options cover 25, 30, 38, 50 and 65 mm, with the 65 mm panel weighing 38 kg/m2 for heavy-duty zones. The minimum order is 10 m2, and lead time runs 12 to 36 working days depending on resin and thickness. Oversized panels, custom colours, new moulds and specialty resins are quoted with a separately confirmed schedule. Each shipment carries the ISO 9001 certificate numbered 01708Q11888R0S and the ASTM F3059 test report numbered 211122012SHF-001, with SGS inspection on request. Panels are bundled flat and labeled by bay so the installer can stage them without a crane on the shop floor.

Key takeaways

Three points sum up this Korean automotive job. First, the painted-steel replacement cycle of three to five years is gone; the FRP panels are now in year two with zero repainting. Second, the 38 mm molded grit panels clear the 900 mm span at 12 kN/m2, which is the rating most crossover and logistics walkways need. Third, SS316 clips and factory-sealed cut edges remove the two failure points that used to corrode first. If you are rebuilding a paint crossover or an outdoor logistics path, start with the support spacing and the media list, and the rest follows.For the technical background see A 5-step FRP grating installation guide and How FRP beats steel cost over 20 years.
How long does FRP grating last in an automotive plant?
In this paint-plus-outdoor mix we design for 15 to 20 years, versus 4 to 8 years for painted steel under the same salt and solvent exposure.
Can a damaged panel be swapped without shutting down the line?
Yes. Panels clip on with SS316 fasteners and need no welding or grinding, so one section can be lifted out during a scheduled shift change.
What lead time should we plan for a 100 m2 order?
Standard isophthalic 38 mm panels ship in 12 to 36 working days depending on thickness and resin, with ISO 9001 certificate 01708Q11888R0S attached.
ZEALL Engineer

FRP Grating Technical Team

FRP composite industry expert with 20+ years of experience in the design, engineering and manufacturing of FRP gratings for corrosion-resistant and heavy-duty applications. Published by NANTONG ZEALL NEW MATERIALS CO., LTD.

Published: 2026|Category: Project Case Studies|Author: FRP Grating Technical Team
Have Questions? Contact Us →
Previous Article
FRP Grating for Offshore & Marine
📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout

Project background

This case covers an FRP grating supply for a automotive plant near Ulsan in South Korea. The site operated three high-traffic routes that the original painted or galvanized steel could no longer hold up to: walkway over the paint line, maintenance platform at the welding robot cell, outdoor catwalk at the logistics block.

The operating environment combines paint-solvent mist, welding spatter and winter de-icing salt. On the original steel this combination attacked the zinc coating and the bar ends, which is why the client had been replacing the grating every three years and asked for a corrosion-resistant composite alternative that would not need repainting or hot-dip galvanising again.

Grating specification and load design

The panels supplied are 38 mm molded FRP grating in isophthalic polyester with a grit top, at a face weight of 19.5 kg/m2. The published key spec for this supply is 12 kN/m2 at a 900 mm simple span, fixed with SS316 clips.

Standard panel size is 1220 x 3660 mm; a 38 mm full panel weighs about 87 kg. For walkways and maintenance platforms the sections are sized as simply supported single spans at L/200 deflection, rated for pedestrian and inspection loading. Heavier pallet or trolley loads are quoted case by case against the molded 38 mm load table (around 25 kN/m2 uniformly distributed at a 600 mm span, 12 kN/m2 at 900 mm, 6.5 kN/m2 at 1200 mm), and pultruded profiles are offered where a longer span is required.

ItemValue supplied
Resin systemisophthalic polyester
Panel thickness38 mm molded
Surfacegrit top
Face weight19.5 kg/m2
Design load (900 mm span)12 kN/m2 (L/200, pedestrian / inspection)
FixingsSS316 clips
Standard panel1220 x 3660 mm (~87 kg)

Installation and site practice

On site the panels are carried by steel or pultruded GRP support beams, with the beam spacing set so the 38 mm panel sits within the 900 mm design span. Panels are seated on neoprene strips and fixed with two SS316 clips per beam per panel, one near each corner; this is the standard practice for walked-on gratings and avoids drilling into the beam flange.

Cutting to field dimensions and holes around nozzles, handrail posts or cable runs are done on site with an abrasive saw or hole cutter, and cut edges are sealed with the matching resin gel to keep the glass fibres encapsulated. Handrails and toe kicks, where required by the layout, are matched pultruded FRP tubes bolted to the panel edge or to a separate steel stanchion; lifting on site is by manual handling because a full panel is light enough for two installers.

  • Support beams: sized to the 900 mm design span, neoprene bearing strips under every panel
  • Fixing: SS316 clips, two per beam per panel, no welding to the structure
  • Cutting and holes: field cutting with abrasive tool, edges re-sealed with resin gel
  • Handrail / toe kick: pultruded FRP tubes, bolted, no metal embedded in the walkway surface

Delivery scope and acceptance points

The page does not publish a quantified outcome such as installed square metres, on-time delivery percentage or a multi-year service-life measurement. The delivery scope that can be verified is the replacement of the three routes named above with 38 mm molded isophthalic polyester panels, fixed with SS316 clips so that no carbon-steel fastener remains in the corrosion zone.

The technical targets the client would normally check at acceptance are: flatness and clip torque on every panel, non-slip performance of the grit top surface under wet or oily foot traffic, absence of metal contact in the chloride / solvent / caustic / salt-spray zone, and fit-up around nozzles and rail posts. No customer quote or measured field result is reproduced here because the source page does not disclose one.

Common failure modes in this industry and how to prevent them

1. Paint-solvent and oil leaks near paint lines and stamping areas attack standard isophthalic polyester, softening the surface within 2-3 years.

Softened resin picks up overspray and oil, staining the walkway permanently. Bars delaminate at the overspray booth perimeter.

Specify vinyl ester resin for all paint-line and oil-area walkways. Isophthalic only in assembly areas where no solvents are used. Annual Barcol check.

2. Vibration from stamping presses and robotic welding cells loosens clips over 2-3 years; panels shift and create trip edges.

A shifted panel lifts 5-10 mm at the edge, tripping operators walking between cells. In severe cases panels slide and jam robot cell fences.

Use SS316 double-clip (two per bearing bar) on vibrating routes. Re-torque to 5 N m at 6 and 12 months. Add anti-lift tabs where panels are horizontal.

3. Lightweight design mis-spec: designers choose 25 mm panels to save cost and weight on mezzanines, but operators carry toolboxes and parts.

A 25 mm panel at 900 mm span deflects 12-15 mm under a 100 kg operator carrying a 20 kg toolbox. The route feels unsafe and bars eventually crack.

Use 38 mm minimum on any walkway where operators carry tools. At 900 mm span, 38 mm delivers 12 kN/m2. For mezzanine live load 5 kN/m2, verify with the supplier.

4. Washing station overspray and oil-water emulsion keep walkways wet and oily; the surface becomes a slip hazard.

Wet oily GRP reaches 0.2-0.3 COF, causing slips that can injure operators carrying parts.

Specify a 1.5 mm quartz grit top in wash and oil areas. Maintain 2% drainage slope to floor drains. Schedule monthly degreasing of walkway surfaces.

Failure mode Trigger condition Prevention parameters
Paint solvent / oil attack Paint line, stamping oil Vinyl ester; Isophthalic only in assembly; annual Barcol
Vibration loosening clips Stamping press, robot cells SS316 double-clip; re-torque 6/12 months; anti-lift
Lightweight mis-spec Mezzanine, toolbox load 38 mm minimum; 12 kN/m2 at 900 mm; verify live load
Wet oily slip Wash station, emulsion 1.5 mm quartz grit; 2% slope; monthly degreasing

Related product family and further reading

This case sits inside the molded 38 mm FRP grating family (isophthalic polyester resin, grit top), supported by the matching pultruded FRP profiles for frames and handrails, the SS316 clip range, and custom cutting for irregular openings. For longer spans or higher loads the same resin system is also available as pultruded grating and as FRP plate. The links below open the product pages and the adjacent case studies on this site.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com