📞 Contact UsHomeProductsCatalogueApplicationsProjectsMarketsBlog🎬 VideosTools💰 CalculatorAbout
FRP Molded Grating Manufacturer · Monolithic Square-Mesh Panels

FRP Molded Grating Manufacturer

FRP Molded Grating · Mono-Directional Square Mesh · Bidirectional Strength — molded fiberglass grating manufacturer for walkways, platforms and general flooring.

ISO 9001 Certified
Direct FRP Grating Master Factory
Exported to 45+ Countries
ISO 9001
Quality Management
45+ Countries
Global Export Network
20+ Years
Manufacturing Experience
Custom OEM/ODM
Engineering Support

FRP Grating Master is an FRP molded grating manufacturer producing monolithic square-mesh fiberglass panels. In the moulding process, continuous glass fibre is woven and fully impregnated with resin, then cured as one integrated panel — so load is shared in both directions, not just along bars. Molded grating is the cost-effective, impact-tolerant choice for general walkways, platforms and flooring in corrosive or non-conductive service.

Overview

Why Molded Grating

Monolithic, Bidirectional Strength

Because the panel cures as a single integrated mesh, strength and impact resistance are uniform in both directions — well suited to walkways and platforms where loads vary.

Cost-Effective General Purpose

Molded grating in orthophthalic polyester is the most economical corrosion-resistant flooring for general industrial, water-treatment and coastal walkways.

Overview

Specifications & Range

What We Manufacture

Molded panels in 25/30/38/50 mm thickness, polyester/isophthalic/vinyl ester resin, gritted or concave anti-slip surfaces. Compare with pultruded grating for long spans.

Applications & Supply

Walkways, platforms, trench covers and stair treads — see walkway, platform and trench covers. Order via contact; full range on products.

Technical Specifications

Molded FRP Grating Technical Specifications & Sizes

As an FRP molded grating manufacturer, we produce one-piece moulded panels in continuous squares for walkways, platforms and trench covers. The table below lists the standard specs we manufacture to.

ParameterStandard RangeNotes
Thickness25 / 30 / 38 / 50 mm38 mm is the platform standard
Mesh size38×38 / 19×19 / 12×12 mm19×19 for fine safety
Standard panel1220×3660 mmCut to size on request
SurfaceGrit-top / Concave / Smooth / CoveredGrit for slip resistance
Resin systemIsophthalic / Vinyl ester / PhenolicPhenolic for fire zones
Typical load classA – C (pedestrian to light vehicle)Per panel thickness

Every panel is cut to your drawing with cut-outs, and supplied with COA, MSDS and load test reports.

Material Comparison

Molded FRP vs Pultruded vs Steel Grating

Molded grating is the most cost-effective corrosion-free panel for short- to medium-span pedestrian duty. The table compares where it wins and where pultruded or steel is better.

PropertyMolded FRPPultruded FRPSteel (HDG)
Economy (short span)BestHigher costLow upfront
Span rangeUp to ~600–900 mmUp to ~1500 mmLong
CorrosionImmuneImmuneRusts
Two-direction strengthYes (interwoven)Bars one directionVaries
WeightLightLightHeavy

See the molded vs pultruded comparison.

Resin Selection

Resin Selection for Molded Grating

Molded panels are available in the same resin systems as pultruded; choose the cheapest resin that meets your environment.

ResinRelative CostChemical ResistanceFire RatingBest For
Isophthalic polyesterBaselineGoodASTM E-84 Class BGeneral walkways and platforms
Vinyl ester+15–25%Excellent (acids, alkalis, H2S)ASTM E-84 Class BChemical, marine, wastewater
Phenolic+20–35%ModerateASTM E-84 Class A (low smoke)Tunnels, rail, fire-critical zones

Send your chemical list — see vinyl ester vs polyester.

Load & Span

Molded Panel Load and Thickness Selection

Molded panels are chosen for pedestrian and light-traffic platforms. Match thickness to span and load.

ApplicationRecommended ThicknessTypical Support Span
Pedestrian walkway25–30 mm molded450–600 mm
General platform38 mm molded600–750 mm
Light pallet truck50 mm molded750–900 mm
Fine-footwear / barefoot safety38 mm, 19×19 mesh600–750 mm

Send span and load and we confirm the panel class before quoting.

Installation

Molded Grating Installation Guide

  1. Lay panels on clean, level support beams with the recommended bearing width.
  2. Secure with stainless clips — minimum 4 per 1220×3660 mm panel, one each corner.
  3. Add clips along long sides in heavy-traffic or wind-uplift zones.
  4. Cut with a carbide-tipped blade; seal cut edges on vinyl ester/phenolic panels.
  5. Leave a 10–15 mm expansion gap between adjacent panels.

See the installation guide and grating clips.

Applications

Where Molded FRP Grating Is Used

Walkways and platforms: the economical one-piece panel for general plant access, stairs and balconies — see walkway grating.

Wastewater treatment: 38 mm vinyl ester molded panels are the standard floor for galleries and tank platforms — see wastewater guidance.

Chemical processing: grit-top molded panels resist acid/alkali splash and stay non-slip when wet.

Manufacturing

Molded Grating Manufacturing Process

Our molded grating is produced by hand lay-up of continuous glass rovings in both directions through a resin bath, cured in a mould and topped with a silica grit surface. This gives uniform two-direction strength and a consistent anti-slip grit top. We offer standard and custom colours (see colour options) and cut-to-size panels via custom FRP grating.

Related Pages

Related Products and Guides

Get Started

Request Your FRP Molded Grating Manufacturer Quote

Email sales@gratingfrp.com · Tel/WhatsApp +86-513-6681-9918 · Nantong, Jiangsu, China

FAQ

FRP Molded Grating Manufacturer FAQ

What is molded FRP grating?
Molded FRP grating is a monolithic, square-mesh panel made by weaving and resin-impregnating continuous glass fibre, then curing it as one integrated panel with bidirectional strength.
When is molded grating preferred?
Molded grating suits general walkways, platforms and flooring where cost-effectiveness and bidirectional impact tolerance matter. For long spans and heavy loads, pultruded grating is better.
What thicknesses and resins do you offer?
Molded panels come in 25/30/38/50 mm thickness, in orthophthalic polyester, isophthalic polyester and vinyl ester resin, with UV-stabilised options.
Can molded grating have anti-slip surfaces?
Yes — molded panels are available with gritted or concave (serrated) anti-slip tops.
What mesh size is available for molded FRP grating?
We produce 38×38, 19×19 and fine 12×12 mm mesh. 19×19 is the common safety choice where small objects or footwear must not slip through.
Do you offer custom colours for molded grating?
Yes. Beyond standard grey we supply a range of stock colours and can match custom colours on request — see our colour options guide.
What is the typical MOQ for molded grating?
Standard production MOQ is around 100 square metres, with small trial orders accepted on request and mixed sizes/resins combined in one container.

Document Preview

Preview mode · For full document, click Download

Download Document

Thank you for your interest. Please fill in your email and company name. Our technical and sales team will contact you within 30 minutes (during working hours) to provide support!

📧 Your information will be sent to sales@gratingfrp.com. We respect your privacy and will never share your data.

Thank You!

Your request has been received successfully.

Our technical and sales team will contact you within 30 minutes (during working hours) to provide the document and professional support!

If you need urgent assistance, please email: sales@gratingfrp.com